Bosch GWS 1400 C Professional Notice Originale page 24

24 | English
With approved abrasive tools, the power tool can be used for
sanding with sanding discs.
The power tool must not be used to grind stone materials
with diamond grinding heads.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Unlocking lever for protective guard
(2) Spindle lock button
(3) On/off switch
(4) Low-vibration auxiliary handle (insulated gripping
a)
surface)
(5) Standard auxiliary handle (insulated gripping sur-
face)
(6) Extraction guard for grinding
(7) Protective guard for grinding
(8) Protective guard for cutting
(9) Cover for cutting
(10) Mounting flange with O‑ring
a)
(11) Carbide grinding head
a)
(12) Grinding disc
Technical Data
Angle grinder
Article number
Rated power input
Power output
A)
Rated no-load speed
Max. grinding disc diameter/rubber sanding
pad diameter
Grinding spindle thread
Max. thread length of grinding spindle
Restart protection
Soft start
Constant electronic control
B)
Weight
Protection class
A) Rated no-load speed for the selection of appropriate application tools in accordance with EN IEC 62841-2-3. The actual no-load speed
must not exceed the rated no-load speed and is therefore lower.
B) Depends on protective guard ((8), (7), (9)) and auxiliary handle ((5), (4)) in use
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.
Values can vary depending on the product, scope of application and environmental conditions. To find out more, visit
www.bosch-professional.com/wac.
Noise/Vibration Information
Noise emission values determined according
to EN IEC 62841-2-3.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 92 dB(A); sound power
level 100 dB(A). Uncertainty K = 3 dB.
1 609 92A 763 | (27.03.2024)
(13) Disc brush (dia. 22.22 mm)
(14) Disc brush (M 14)
(15) Cutting disc
(16) Diamond cutting disc
(17) Clamping nut
(18) Quick-clamping nut
(19) Two-pin spanner for clamping nut/round nut
(20) Handle (insulated gripping surface)
(21) Grinding spindle
(22) Hand guard
(23) Rubber sanding pad
(24) Sanding sheet
(25) Round nut
(26) Cup brush
a)
(27) Conical brush
(28) Diamond annular cutter
a)
(29) Open-ended spanner
(30) Extraction guard for cutting with cutting guides
a) Accessories shown or described are not included with the
GWS 1000
3 601 H28 8..
W
W
–1
min 11,800
mm
mm
kg 2.2–2.5
Wear hearing protection!
Vibration total values a
determined according to EN IEC 62841-2-3:
Surface grinding (roughing) and abrasive cutting:
a
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
a)
product as standard. You can find the complete selection of
accessories in our accessories range.
GWS 1400 C GWS 1400
3 601 H24 2.. 3 601 H24 8..
1000 1400
630 820
11,800
125 125
M 14 M 14
22 22
● ●
● ●
– ●
2.2–2.5
/ II / II
(triax vector sum) and uncertainty K
h
2 2
= 5.6 m/s , K = 1.5 m/s ,
h
a)
a)
a)
GWS 14-125
3 601 H24 8..
1400 1400
820 820
11,800 11,800
125 125
M 14 M 14
22 22
● ●
● ●
● ●
2.2–2.5 2.2–2.5
/ II / II
Bosch Power Tools