IKEA GENOMFRYSA Mode D'emploi page 7

Installation
The appliance must be handled and installed by two or more
persons - risk of injury. Use protective gloves to unpack and install
- risk of cuts.
Installation, including water supply (if any), electrical
connections and repairs must be carried out by a qualified
technician. Do not repair or replace any part of the appliance
unless specifically stated in the user manual. Keep children away
from the installation site. After unpacking the appliance, make
sure that it has not been damaged during transport. In the event
of problems, contact the dealer or your nearest Aftersales Service.
Once installed, packaging waste (plastic, styrofoam parts etc.)
must be stored out of reach of children - risk of suffocation. The
appliance must be disconnected from the power supply before any
installation operation - risk of electric shock. During installation,
make sure the appliance does not damage the power cable - risk
of fire or electric shock. Only activate the appliance when the
installation has been completed.
Be careful not to damage the floors (e.g. parquet) when
moving the appliance. Install the appliance on a floor or support
strong enough to take its weight and in a place suitable for its size
When contacting our Service Provider, please state the codes
provided on your product's identification plate.
The model information can be retrieved using the QR-Code
reported in the energy label. The label also includes the model
identifier that can be used to consult the
https://eprel.ec.europa.eu database portal.
*On the rating plate the article number is 8 digits
Inspection check list
Please follow the inspection checklist before using your appliance.
If any answer is NOT please follow the relevant action.
Please remember to write down the product serial number and
article number as required and attach your receipt to this page.
Product serial number (rating plate) *
Product artical number (rating plate) **
Purchasing date
Consideration Tray
Check that the tube is inside the tray
Making sure gasket seals all around the door
when the door is closed
Checking no collision between parts/forniture
while opening/closing the cooling door
Secure the installation inside any kitchen
system and fixed as required
General information
The drawers, baskets and shelves should be kept in their current
position unless otherwise specified in this quick guide. The light
system inside the refrigerator compartment uses LED lights,
allowing for better lighting than with traditional light bulbs, as
Technical data
IKEA GENOMFRYSA
Brand Model
and use. Make sure the appliance is not near a heat source and
that the four feet are stable and resting on the floor, adjusting
them as required, and check that the appliance is perfectly level
using a spirit level. Wait at least two hours before switching the
appliance on, to ensure that the refrigerant circuit is fully efficient.
WARNING: When positioning the appliance, ensure the supply
cord is not trapped or damaged.
WARNING: To avoid a hazard due to instability, positioning
or fixing of the appliance must be done in accordance with the
manufacturer instructions. It's forbidden to place the refrigerator
in such way that the metal hose of gas stove, metal gas or water
pipes, or electrical wires are in contact with the refrigerator back
wall (condenser coil).
To guarantee adequate ventilation, leave a space on both sides
and above the appliance. The distance between the rear of the
appliance and the wall behind the appliance should be 50 mm, to
avoid access to hot surfaces. A reduction of this space will increase
the Energy consumption of product. Please remove the power
cord from condenser hook during installation before connecting
product to power supply.
well as for very low energy consumption. Doors and lids of the
refrigeration appliance should be removed before disposal in the
landfill, to avoid children or animals getting trapped inside.
10
Freezing
capacity consumption
(kg/24h) (kwh/year)
To download the full version visit www.ikea.com
XXXXXXXXXXXXX XXXXXXXXX
XXXXXXXXXXXXX XXXXXXXXX
XXXXXXXXXXXXX XXXXXXXXX XXXXXXXXXXXXX XXXXXXXXX
XXXXXXXXXXXXX XXXXXXXXXXXXX XXXXXXXXXXXXX
XXXXX XXXXX XXXXX XXXXX XXXXX
XXXXX XXXXX XXXXX XXXXX XXXXX
XXXXX XXXXX XXXXX XXXXX XXXXX
If the answer is YES Actions to do if NOT
Put the tube inside the tray
No action
Refer to the AI - door
No action
allignment step
Refer to the AI - door
No action
allignment step
Follow the AI for the proper
No action
installation
218 40
Energy Noise level
(dba)
7
**On the rating plate the
serial number is 12 digits
F
Energy class