SilverCrest SHBS 3.7 E1 Instructions D'utilisation Et Consignes De Sécurité page 12

Trimming the hairline
(Precision trimmer attachment
Use the precision trimmer attachment
shape moustache, whiskers, sideburns or eyebrows.
Put the edge of the attachment at the desired hairline height
and move the hair and beard trimmer unit
Shaving (contours)
(Shaving attachment
Note: Your skin must be clean and dry. The shaving attachment
is only suitable for shaving hairlines.
Hold the hair and beard trimmer unit
the skin surface and gently guide it over your face.
Shave against the direction of your beard growth.
Stretch your skin in complicated areas, such as the chin,
to achieve better results.
Trimming nose and ear hair
(Nose/ear hair trimmer attachment
(see Fig. J)
Insert only the metal tip slowly into a nostril or an ear.
Slowly move the hair and beard trimmer unit
circular motion to trim the hair.
Cleaning with the cleaning brush
Switch the product off using the ON/OFF button
If cutting attachments (
( – ) is attached on the product, remove it before
1 3
cleaning as described in the chapter "Operation". Remove
the attachment by pressing the trimmer with your thumbs
from the front (see Fig. A).
Remove the hair remnants from the attachment using the
cleaning brush .
21
Ordering replacement parts
Replacements for the following parts can be ordered online:
Shaving attachment
4
Precision trimmer attachment
Nose/ear hair trimmer attachment
Hair trimmer attachment
7
Beard trimmer attachment
8
Item number: 444777_2307
Website: www.optimex-shop.com
12 GB/IE/NI
)
5
to shorten and
5
downwards.
9
)
4
at a right angle to
9
with a
9
– ) or comb attachments
4 8
5
6
Cleaning and care
Never immerse the product, the USB Type A to C cable
and the power supply in water or other liquids during corded
use or rinse under running water.
Always switch off the product before cleaning it.
The comb attachments
attachment
6
other liquids.
Note: Let them dry before using again.
Do not use aggressive or abrasive cleaning agents.
Wipe down the product with a slightly damp cloth.
If you are not using the product for extended periods,
4
store it in the storage bag
Hair and beard trimmer unit
Wipe the casing of the hair and beard trimmer unit
a damp cloth.
Comb attachments
Remove the comb attachment
attachment
1
)
using again.
6
Precision trimmer
trimmer attachments
Remove the attachment from the hair and beard trimmer
unit by pressing it with the thumb towards the rear
9
(see Fig. A).
Remove the hair remnants from the attachment using the
cleaning brush
Note: It is recommended that you oil the blades before first
. use and after cleaning to guarantee complete functionality
11
(see Fig. G, H, I). Always switch off the product before oil
the blade. Apply one or two drops of blade oil
the blades and distribute them evenly. Wipe off any excess
oil with a cloth. You can also use any acid-free oil (such as
sewing machine oil).
Note: The blades can be oiled with or without the comb
attachment
1
Nose/ear hair trimmer attachment
Remove the nose/ear hair trimmer attachment
with water and let it dry completely before using it again.
Shaving attachment
Do not detach the shaving foil from the shaving foil frame,
and do not clean it using the cleaning brush
Note: From time to time, oil the cutting blade with a few
drops of acid- free oil (e.g. sewing machine oil). Attach the
shaving attachment
and let it run for a few seconds without using it. Using a soft
cloth, wipe off the surplus oil, if necessary.
Remove the shaving attachment
Press the button on the side of the shaving attachment
and remove the shaving foil frame. While removing the
shaving foil frame, only hold it at the side and do not press
against the shaving foil.
, , and nose/ear hair trimmer
1 2 3
can be cleaned with water. Do not use any
.
23
9
, ,
1 2 3
, , . Rinse the comb
1 2 3
, , with water and let it dry before
2 3
, hair trimmer and beard
5 7
8
included in the delivery.
21
, or .
2 3
6
4
to the hair and beard trimmer unit
4
.
4
16
with
9
between
20
. Rinse it
6
.
21
9
4