Technical Data; Noise/Vibration Information - Bosch GCM 80 SJ Professional Notice Originale

OBJ_BUCH-2154-002.book Page 22 Monday, June 16, 2014 2:55 PM
22 | English

Technical Data

Sliding Mitre Saw
Article number
3 601 M19 ...
Rated power input
No-load speed min
Reduced starting current
Weight according to
EPTA-Procedure 01/2003
Protection class
Permissible workpiece dimensions (maximal/minimal) see page 25.
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Dimension of suitable saw blades
Saw blade diameter
Blade body thickness
Mounting hole diameter
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 61029-1, EN 61029-2-9.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 28.04.2014

Noise/Vibration Information

Sound emission values determined according to
EN 61029-2-9.
Typically the A-weighted noise levels of the product are:
Sound pressure level 93 dB(A); Sound power level
106 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 61029:
2 2
a =3,0 m/s , K=1,5 m/s .
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 61029 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
1 609 92A 0HN | (16.6.14)
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
GCM 80 SJ
applications, with different accessories or poorly maintained,
GCM 800 SJ
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
GCM 8000 SJ
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
... 0.. ... 06.
when it is running but not actually doing the job. This may sig-
W 1400 1250
nificantly reduce the exposure level over the total working pe-
-1
5500 5500
riod.
  Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
kg 13.5 13.5
terns.
/II /II
Assembly
 Avoid unintentional starting of the machine. During as-
mm 210–216
Delivery Scope
mm 1.3–1.8
Before starting the operation of the machine for the first time,
mm 30
check if all parts listed below have been supplied:
– Sliding mitre saw with premounted saw blade
– Material clamp 5
– Hex key 34
– Metal bar of tilt protector 33
– Oil damper 39 with 2 fixing screws 40
Note: Check the power tool for possible damage.
Before further use of the machine, check that all protective
devices are fully functional. Any lightly damaged parts must
be carefully checked to ensure flawless operation of the tool.
All parts must be properly mounted and all conditions fulfilled
that ensure faultless operation.
Damaged protective devices and parts must be immediately
replaced by an authorised service centre.
Stationary or Flexible Mounting
 To ensure safe handling, the machine must be mounted
Mounting to a Working Surface (see figure A)
– Fasten the power tool with suitable screw fasteners to the
Mounting to a Bosch Saw Stand
With the height-adjustable legs, Bosch GTA saw stands pro-
vide firm support for the power tool on any surface. The work-
piece supports of the saw stand are used for underlaying long
workpieces.
 Read all safety warnings and instructions included with
sembly and for all work on the machine, the power plug
must not be connected to the mains supply.
on a level and stable surface (e. g., workbench) prior to
using.
working surface. The mounting holes 1 serve for this pur-
pose.
the worktable. Failure to observe safety warnings and in-
structions can lead to electrical shock, fire and/or cause
serious injuries.
Bosch Power Tools