Husqvarna 362XP Manuel D'utilisation page 34

Engine
Cylinder volume,
3
cu.in/cm
Cylinder bore, inch/mm
Stroke, inch/mm
Idle speed, rpm
Power, kW/ rpm
Ignition system
Manufacture
Type of ignition system
Spark plug
Electrode gap, inch/mm
Fuel and lubrication
system
Manufacturer
Carburetor type
Fuel capacity,
US pint/litre
Oil pump capacity at 8500
rpm, ml/min
Oil capacity, US pint/litre
Type of oil pump
Weight
Without bar and chain,
Lbs/kg
Chain/bar
Recommended bar lengths,
inches/cm
Usable cutting length,
inches/cm
Chain speed at max.
power, m/sec
Pitch, inch/mm
Thickness of drive link,
inch/mm
Number of teeth on drive
sprocket
34
– English
TECHNICAL DATA
362XP 365 372XP
3,8/62,4 4,0/65,1 4,3/70,7
1,85/47 1,89/48 1,97/50
1,4/36 1,4/36 1,4/36
2 700 2 700 2 700
3,4/ 9 600 3,4/ 9 300 3,9/ 9 600
SEM SEM SEM
CD CD CD
Champion Champion Champion
RCJ 7Y/ RCJ 7Y/ RCJ 7Y/
NGK BPMR NGK BPMR NGK BPMR
7A 7A 7A
0,02/0,5 0,02/0,5 0,02/0,5
Walbro Walbro Walbro
HD12 HD12 HD12
1,63/0,77 1,63/0,77 1,63/0,77
4–20 4–20 4-20
0,89/0,42 0,89/0,42 0,89/0,42
Automatic Automatic Automatic
13,2/6,0 13,2/6,0 13,4/6,1
XPG:13,7/6,2 XPG:13,8/6,3
13-24"/33-61 15-28"/38-71 15-28"/38-71
12-23"/31-58 14-27"/35-69 14-27"/35-69
21,4 20,7 21,4
3/8"/ 9,52 3/8"/ 9,52 3/8"/ 9,52
0,325"/ 8,25
0,050"/1,3 0,050"/1,3 0,050"/1,3
0,058"/1,5 0,058"/1,5 0,058"/1,5
0,063"/1,6 0,063"/1,6 0,063"/1,6
7 7 7
RECOMMENDED CUTTING EQUIPMENT
FOR CANADA
The following is a list of recommended cutting equipment
for Class 1A and 1B Chainsaws.
The combinations of powerhead, bar and chain meet all
requirements outlined in the CSA Z62.1-95 Chainsaws and
Z62.3-96 Chainsaw Kickback standards.
The guide bar nose radius is determined by either the
maximum number of teeth in the nose sprocket or the
corresponding maximum nose radius of a solid bar.
As we are listing the maximum guide bar nose radius, you
may use a guide bar with smaller nose radius than in our
list. For guide bars of the same length, all sprocket-nose
guide bars of the same pitch and having the same number
of sprocket teeth may be considered to have equivalent
kickback energy.
A hard nose bar having the same length and nose radius as
a sprocket-nose bar may be considered to have equivalent
or less kickback energy than the sprocket-nose bar.
We recommend that you as replacement use the listed bars
and chains or "Type C Low-Kickback Saw Chains" which
are available at your dealer.
Model 362XP Special
Guide bar
Length Pitch Max nose
inch inch radius
15 0,325 10T
16 0,325 10T
18 0,325 10T
20 0,325 12T
15 3/8 11T
16 3/8 11T
18 3/8 11T
20 3/8 11T
24 3/8 11T
Model 365 Special and 372XP
Guide bar
Length Pitch Max nose
inch inch radius
15 3/8 11T
16 3/8 11T
18 3/8 11T
20 3/8 11T
24 3/8 11T
28 3/8 11T
Note: For the chains above you are free to choose between
0,050", 0,058" and 0,063" gauge drive link for the corresponding
bar, see the table below.
0,050"/1,3 mm 20BP 20LP
0,058"/1,5 mm H25/21VB H21/21LP H42/73LP EM S48/73LG
0,063"/1,6 mm 22BP 22LP
The combinations of powerhead, bar and chain have been
investigated in accordance with the vibration requirements of
ANSI B 175.1-2000.
!
WARNING! These models of chain saws are
capable of severe kickback that could result in
serious injuries to the user. Do not operate these
saws unless you have extraordinary cutting needs
and experience and specialized training for dealing
with kickback. Saws with significantly reduced
kickback potential are available. Always use the
safest saw and cutting equipment applicable to
your cutting need.
Saw chain
Husqvarna H25/H21 or
Oregon 21BP/21LP
Husqvarna H42/EM S48 or
Oregon 73LP/73LG/73V
Saw chain
Husqvarna H42/EM S48 or
Oregon 73LP/73LG
72LP 72LG 72V
73V
75LP 75LG 75V