Makita DLS110 Manuel D'instructions page 22

9. The wireless unit can produce electromagnetic
fields (EMF) but they are not harmful to the user.
10. The wireless unit is an accurate instrument. Be
careful not to drop or strike the wireless unit.
11. Avoid touching the terminal of the wireless
unit with bare hands or metallic materials.
12. Always remove the battery on the product
when installing the wireless unit into it.
13. When opening the lid of the slot, avoid the
place where dust and water may come into the
slot. Always keep the inlet of the slot clean.
14. Always insert the wireless unit in the correct
direction.
15. Do not press the wireless activation button
on the wireless unit too hard and/or press the
button with an object with a sharp edge.
16. Always close the lid of the slot when
operating.
17. Do not remove the wireless unit from the slot
while the power is being supplied to the tool.
Doing so may cause a malfunction of the wireless unit.
18. Do not remove the sticker on the wireless unit.
19. Do not put any sticker on the wireless unit.
20. Do not leave the wireless unit in a place where
static electricity or electrical noise could be
generated.
PARTS DESCRIPTION
► Fig.2
1 Slide pole
5 Holder
9 Kerf board
13 Blade guard
Adjusting bolt (for maxi-
17
mum cutting capacity)
21 Releasing lever (for turn
base)
► Fig.3
1 Switch trigger
5 Switch (for laser line)
(For DLS111, DLS112
only)
9 Wireless activation
button
13 Guide fence (lower
fence)
17 Bevel angle scale
45° adjusting bolt (for
21
bevel angle)
2 Stopper pin (for carriage
sliding)
6 Turn base
10 Blade case
14 Knob (for bevel angle)
18 Stopper arm
22 Grip (for turn base)
Lock-off button
2
6 Battery indicator
10 Wireless activation lamp
14 Guide fence (upper
fence)
18 Releasing lever (for 48°
bevel angle)
- -
22 ENGLISH
21. Do not leave the wireless unit in a place sub-
ject to high heat, such as a car sitting in the
sun.
22. Do not leave the wireless unit in a dusty or
powdery place or in a place corrosive gas
could be generated.
23. Sudden change of the temperature may bedew
the wireless unit. Do not use the wireless unit
until the dew is completely dried.
24. When cleaning the wireless unit, gently wipe
with a dry soft cloth. Do not use benzine, thin-
ner, conductive grease or the like.
25. When storing the wireless unit, keep it in the
supplied case or a static-free container.
26. Do not insert any devices other than Makita
wireless unit into the slot on the tool.
27. Do not use the tool with the lid of the slot dam-
aged. Water, dust, and dirt come into the slot may
cause malfunction.
28. Do not pull and/or twist the lid of the slot more
than necessary. Restore the lid if it comes off
from the tool.
29. Replace the lid of the slot if it is lost or
damaged.
SAVE THESE INSTRUCTIONS.
3 Vertical vise
7 Pointer (for miter angle)
Adjusting screw (for
11
laser line)
15 Hex wrench
19 Battery cartridge
- -
3 Hole for padlock
7 Mode indicator
11 Hose (for dust
extraction)
15 Dust bag
19 Latch lever (for bevel
angle)
- -
4 Releasing button (for
right side bevel angle)
8 Miter angle scale
Range adjustment screw
12
(for laser line)
Adjusting screw (for
16
lower limit position)
20 Lock lever (for turn base)
- -
4 Lid (for wireless unit)
(For DLS111 only)
8 Check button
12 Stopper pin (for carriage
elevation)
0° adjusting bolt (for
16
bevel angle)
20 Pointer (for bevel angle)
- -