BorMann PRO BTC3500 Mode D'emploi page 10

EN
20. Warning:
The use of any other accessory or attachment other than recommended it this operating instruction or the catalog may present a risk of personal injury.
21. Have your tool repaired by an expert.
This electric appliance is in accordance with the relevant safety rules repairing of electric appliances may be carried out only by experts otherwise it may cause
considerable danger for the user.
22. Connect the dust extraction device.
Wherever there are facilities for fitting a dust extraction system, make sure it is connected and used.
Warning! This electric tool generates an electro-magnetic field during operation. This field can impair active or passive medical implants under certain
conditions. In order to prevent the risk of serious or deadly injuries, we recommend that persons with medical implants consult with their physician and the
manufacturer of the medical implant prior to operating the electric tool.
Special safety information
Caution! This tile cutting machine is designed for wet cutting only. The machine may be operated only with a non-segmented diamond cutting wheel.
• Wet hands: Never touch the electrical components of the machine (e.g. switches) with wet hands.
• Plug-in connections: All plug-in connections must be located in a dry place and must not lie on the floor.
• Cooling the cutting wheel: Make sure that the cutting wheel is cooled with water during the complete cutting process.
• Dry cutting: Never carry out dry cuts with cutting wheels designed for wet cutting.
• Dust protection: Always wear a protective dust mask when cutting tiles.
• Diamond cutting wheels: Do not feed the tile into the machine any faster than the cutting wheel can cut.
• Use only cutting wheels which are designed for a minimum speed of 3000 min-1.
• Selecting the cutting wheel Select the diamond cutting wheel to suit the material you want to cut.
• Fitting the cutting wheel: Before you install the cutting wheel, check the spindle, the spindle nut and the flanges for damage, wear or a loose fit. Replace
damaged or worn parts without delay.
• Direction of rotation of the cutting wheel: Check the direction arrow on the cutting wheel; the arrow must point in the same direction as the direction in
which the motor shaft rotates.
• Cutting wheel spindle: Make sure that the diameter of the hole in the cutting wheel is the same as the diameter of the cutting wheel spindle on the machine.
• Cutting wheel guard: Only use the tile cutting ma- chine with a properly fitted and adjusted cutting wheel guard.
• Cutting wheel speed: Do not exceed the safe operating speed of the cutting wheel.
• Sanding/grinding with the cutting wheel: Do not try to use the cutting wheel for sanding or grinding jobs, e.g. to sand/grind the edge of a cut tile. Also, do
not use the machine for radius cuts or round cuts. This tile cutting machine is suitable only for household use.
• Cutting wheel stop time: After the machine has been switched off, the cutting wheel needs 40 seconds to come to a standstill. Wait until the cutting wheel
has stopped completely, pull the power plug out of the socket outlet, and only then touch the cutting wheel if necessary.
• Avoid all contact with the rotating cutting wheel when the machine is in operation.
• The electric tool must never be used without the PRCD plug supplied with it.
• Keep water away from electrical parts of the tool and from persons in the work area!
• If the power plug or the power cable are damaged they must be replaced either by the manufacturer or by a service company authorized by the manufacturer.
• To comply with the requirements imposed by the safety regulations, all technical modifications which change the equipment's characteristics (e.g. speed)
must be left strictly to the manufacturer.
• Keep this safety information in a safe place.
Special safety instructions for stone cutting machines
• Place the stone cutting machine on a level work surface with stable footing before using it. Ensure that there is sufficient room for freedom of movement.
• In order to avoid a dust hazard, the machine may only be used in the wet area. This is also mandatory because the diamond cutting wheel is only suitable
for wet cutting.
• Always fill the tube with water before working.
• The machine may only be operated in sufficiently ventilated rooms.
• Attention! Never leave the motor running in closed or spatially-constrained rooms. The exhaust gases contain toxic carbon monoxide!
• As a basic rule, switch on the equipment before material contact.
• The elevated safety regulations for wet operation apply for this stone cutting machine. All safety measures to prevent elevated contact voltages must be
applied.
• Electrical cable wires may not come into contact with water or water vapour.
• Before commencing work, check the equipment and mains cable for damage.
• Check whether the moving parts function faultlessly and do not jam and make sure that no parts are damaged.
• The mains voltage must match the specifications on the type plate of the machine.
• Only use approved extension cables for use out- doors.
• When using a cable reel, completely unwind the cable in order to prevent the cable from heating up.
• When working outside, the electrical outlet must be equipped with a residual current circuit breaker.
• Observe the motor and diamond cutting wheel direction of rotation.
• Only cut one workpiece at a time.
10
WWW.NIKOLAOUTOOLS.GR