Publicité
Les langues disponibles
Les langues disponibles
Speedaire Operating Instructions and Parts Manual
Hose Installation and Replacement
(See Figure No. 2 below)
Hose Removal
1. Turn off and disconnect the supply to reel and
release hose line pressure.
2. Pull out approximately 2m(6ft) of hose and
allow the drum the latch.
3. Remove the outlet nozzle, gun or tool and
hose stopper. Unlatch the reel and carefully
allow the hose to slowly rewind until there is
no spring tension remaining.
4. Manually unwind the hose assembly from the
drum. Carefully disconnect and remove the
hose from plumbing inside the reel.
Hose Installation or Replacement
5. Connect your new hose assembly to
plumbing in the reel, using PTEF tape or pipe
thread sealant.
6. Manually rotate the drum assembly (away from
the roller guides) and manually recoil the hose
onto the drum.
7. Add tension to the reel by carefully rotating the
drum and hose assembly towards the roller
guides (4) complete turns. Slide the hose
through the roller guides and allow the reel to
latch.
Fit the hose stopper to the hose end, release
8.
the drum latch and slowly allow the hose to
slooly rewind onto the reel.
Plumbing
Figure No. 2
Troubleshooting Chart
Sympton
A. Drum losing tension
B. Poor retracting
C. Hose will not latch at
desired length
D. Leakage (the swive)
Note : Final spring adjustment is accomplished
by adding or removing wraps of hose around
the drum. Refer to "Adjust Spring Tension".
Spring Canister removal
(See Figure No.3 below)
1. Pull out approximately 1m(3ft) and latch
the reel.
2. Remove the outlet nozzle, gun or tool and
hose stopper.
3. Carefully unlatch the reel and firmly hold
the drum. Allow the drum to slowly unwind
until it stops and no spring tension remains.
4. Carefully remove the 4sets of nuts and
washers located around the drum assembly.
5. Carefully remove both the front and
back spring canister covers together as
an assembly.
inside which can cause severe injury if
not handled correctly.
6. Carefully sit the drum canister down so
as the flat inner plate flat is facing up.
7. Carefully remove the flat inner plate
to expose the spring.
8. Inspect and replace the complete
drum assembly if the spring is found to be
damaged.
Do not
remove
this bolt
for safety
Spring Canister
Ratchet
Latch
Spring Canister Replacement
1. Slide the flat inner plate over the shaft on
the reel.
Possible Cause (s)
1. Heavy Attachement
(Outlet nozzle, gun or tool)
2. Spring is fatigued
3. Wrong hose assembly.
Spring has broken or has
1.
lost all tension.
1. Incorrect operation
2. Latch assembly is worn.
1. Swivel seals are worn
31XG62, 31XG63, 31XG64, 31XG66,
31XG67, 31XG68 & 31XG70
2.
3.
Note : The spring will automatically locate
itself into the center boss when you re-
tension the reel.
4. Replace all the washers and nuts around
5. Turn the drum counter clockwise until you
There is a large spring
6. Feed the hose through the hose guide, fit
Latch Replacement
1. Working from the swivel side of the reel,
2.
Figure No. 3
3.
Remove only
4. Remove the 4 large bolts holding the
4 bolts to
remove
spring
canister.
5. Slide the support arm off the axle.
6. Inspect the latch assembly and replace
7. Assembly is a reversal of the disassembly
Corrective Action
1. Add spring tension.
2. Add spring tension.
Replace Spring canister if required.
3. Fit correct length hose.
1. Replace Spring canister.
1. Reel latches on first, second or third "click".
After the third click the reel automatically rewinds
2. Replace the latch assembly
1. Replace swivel seals. See " Replacement of Swivel Seals".
3
Check the correct orientation of the
spring locating boss. Remove the boss
from the middle of the spring canister and
slide the boss onto the shaft on the reel
Carefully hold the center of the spring up
in the middle of the drum, at the same
time slide the drum assembly over the
center boss on the shaft.
the outside of the drum assembly and
securely tighten.
feel the spring start to tension, then turn
the drum three complete turns and latch
the drum.
the hose stopper, then unlatch the drum.
The hose stoppers should now sit snuggly
against the hose guide
remove the 4 bolts holding the swivel body
to the axle, then remove the swivel body.
Remove the circlip holding the axle
bearing in place.
Remove the nut and bolt holding the
roller guide to the support arm.
support arm to the mounting bracket
located below the swivel body.
any worn or damaged parts.
procedure.
E
E
N
N
G
G
L
L
I
I
S
S
H
H
Publicité
