Publicité
Les langues disponibles
Les langues disponibles
Turning plate and mixing axle (Fig.15 on page 14) - 222843
GB
Part no.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Speed control assembly (Fig.16 on page 15)
Part no.
1
2
A
3
4
5
6
7
8
9
B
10
11
12
13
Precautions
• The appliance should only be handled by highly qualified peo-
ple who follow the safety measures described in this manual.
• In case of rotation of personnel, training should be provided
in advance.
• The appliance is equipped with safety devices at dangerous
points. However, it is recommended not to touch the blade
and moving components.
• Before starting maintenance operations, disconnect it from
the power supply.
• Carefully assess residual risks when protective devices are
removed for cleaning and maintenance.
• Cleaning and maintenance require great concentration.
• Is absolutely necessary a regular control of the power supply
24
Part name
Quantity
Screw (M6 x 25)
Turning plate
Washer
Nut (M18)
Bowl guard
Inner gear
Screw (M8 x15)
Gear
Bearing (6203)
Bearing (6204)
Oil seal (25x50x10)
Key (5x18)
Drive axle
Pin
Part name
Quantity
Rod
Nut
Spring
Shaft
Fork
Pin (3X20)
Knot
Steel ball bearing
Spring
Block cover
Screw (M5X10)
Shaft
Lever
cord. A frayed or damaged cord can expose users to great risk
of electric shock.
• If the device shows anomalies, do not use it or try to repair it:
6
please contact the supplier.
• Do not use the appliance for frozen foods or any products
1
other than food.
1
• Do not wear loose fitting clothing such as scarf, etc and long
hair should be tied up and keep away from the moving parts.
1
• The manufacturer and/or the seller are not responsible in the
1
following cases:
- if the appliance has been handled by unauthorised person-
1
nel;
1
- if some parts have been replaced with non-original spare
parts;
1
- if the instructions included in this manual are not followed
1
precisely;
- if the cutter has not been cleaned and oiled with the right
1
products.
1
Safety system installed
1
Mechanical safety system
1
The appliance is equipped with 3 safety switches. The machine
only be started with all the safety switches are at the proper
1
positions:
Bowl position safety switch: The machine can be started up
once the bowl is positioned at the correct position.
Bowl guard safety switch: The machine can only be started up
once the bowl guard is in the closed position.
1
Lift up lever safety switch: The machine can only be started up
1
once the lift up lever is located in the upwards position.
1
Even though CE version appliances are provided with electrical
1
and mechanical protections (when the appliance is operating
1
and for maintenance and cleaning operations), there are still
RESIDUAL RISKS that cannot be eliminated completely; these
1
risks are specified in this manual under "WARNING! / DAN-
GER! / CAUTION! ". The moving parts of the machine can cause
1
injuries.
3
Preparation before use
3
• Remove all protective packaging and wrapping.
1
• Check that the device is in good condition and with all ac-
1
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
1
device.
1
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Publicité
