Publicité
Instructions de montage :
Enlever le boulon d'axe du coté gauche du pied de fourche avec une clé de 22mm.
Remplacer ce boulon par le boulon fourni dans le kit R&G puis serrer au couple recommandé.
Insérer un écrou et une rondelle sur l'axe (SB103) (l'extrémité avec l'extrémité tournée vers le
bas), engager l'écrou de façon à ce que l'insert en plastic de l'écrou soit complètement engagé.
Passer l'axe avec écrou et rondelle à travers la protection crash (B0442 M6) et à travers
l'entretoise en métal (S0662), (photo du haut).
Placer cet ensemble à travers l'axe de roue avant du coté droit, en vous assurant que l'extrémité
tournée la plus longue se place à travers le centre du boulon R&G installé au pied de fourche
coté gauche. Placer le patron sur l'entretoise en métal à l'intérieur de l'extrémité de l'axe de
roue du coté droit du pied de fourche.
Placer l'entretoise en métal restante (S0661) et la protection crash autour de l'extrémité de l'axe
du coté gauche. L'entretoise en métal devrait se placer autour de la tête du boulon.
Insérer la rondelle et l'écrou du kit sur le filetage puis serrer jusqu'à ce que les 2 écrous soient
engagés dans le Nylon et que les longueurs dépassants de chaque coté soient égales (assurez
vous que le logo R&G soit bien vers le haut de la protection). NE PAS BLOQUER – les écrous de
Nyloc fixent l'ensemble.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
Outils requis
Clés plates 2x 10mm
Jeu de clés de 22mm.
ISSUE 1 15/05/2013 (AR)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
Email:
info@rg-racing.com
Publicité
