Télécharger
Partager
Imprimer la page
  1. Manuels
  2. Marques
  3. R&G Manuels
  4. Accessoires de moto
  5. FP0279
  6. Instructions de montage

R&G FP0279 Instructions De Montage

Masquer les pouces
1
2
3
4
5
6
7
8
9

Publicité

Liens rapides

Télécharger ce manuel
Page 1 of 9
FP0279
FITTING INSTRUCTIONS FOR FP0279
T
.
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
.
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
.
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
.
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
.
MOUNTING TO THE BIKE
I
,
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
.
THESE RUBBER WASHERS CAN BE THROWN AWAY
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
WWW.RG-RACING.COM
R&G Racing
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
www.rg-racing.com
Email:
info@rg-racing.com

Publicité

loading

Manuels Connexes pour R&G FP0279

Sommaire des Matières pour R&G FP0279

  • Page 1 Page 1 of 9 FP0279 FITTING INSTRUCTIONS FOR FP0279 HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
  • Page 2 Page 2 of 9 FP0279 TOOLS REQUIRED GENERAL TORQUE SETTINGS Socket set M4 BOLT = 8Nm • Rachet • M5 BOLT = M6 BOLT = M8 BOLT = 20Nm 0 BOLT = 40Nm M12 BOLT = 40Nm LEGEND ITEM NO.
  • Page 3 Page 3 of 9 FP0279 FITTING INSTRUCTIONS To start this fitting process, place the M8 Nyloc Nut (Item 7) onto THE M8 end of the spindle • bar (Item 3) and tighten until at least a minimum of 2 threads are through the Nyloc.
  • Page 4 Page 4 of 9 FP0279 MONTAGEANLEITUNG FÜR FP0279 EILE SIND AUF DEN NACHFOLGENDEN EITEN ABGEBILDET UND GEKENNZEICHNET IE ABGEBILDETEN EILE DIENEN LEDIGLICH ZUR RKLÄRUNG Ü BERPRÜFEN IE ZUERST DASS ALLE EILE VORHANDEN SIND ESEN IE DIE ONTAGEANLEITUNG KOMPLETT DURCH BEVOR...
  • Page 5 Page 5 of 9 FP0279 SIE BENÖTIGEN FOLGENDES WERKZEUG: ALLGEM. ANZUGSDREHMOMENT: Satz Steckschlüssel M4 SCHRAUBE = 8Nm • Verlängerung • M5 SCHRAUBE = M6 SCHRAUBE = M8 SCHRAUBE = 20Nm 0 SCHRAUBE = 40Nm M12 SCHRAUBE = 40Nm LIEFERUMFANG ARTIKEL NR.
  • Page 6 Page 6 of 9 FP0279 MONTAGEANLEITUNG Als Erstes montieren Sie die M8 selbstsichernde Mutter (Artikel 7) am M8-Ende der • Verbindungsstange (Artikel 3) und festziehen bis mindesten 2 Gewinde durch die Mutter sind. Unsere Empfehlung für die Montage: benutzen Sie eine kleine Menge Sekundenkleber oder Loctite •...
  • Page 7 Page 7 of 9 FP0279 NOTICE DE MONTAGE POUR FP0279 E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS E PAS PROCEDER AU MONTAGE TANT QUE VOUS N...
  • Page 8 Page 8 of 9 FP0279 OUTILS REQUIS VALEURS DE SERRAGE Clé à cliquet M4 BOULON = 8Nm • Douille • M5 BOULON = 12Nm M6 BOULON = 15Nm M8 BOULON = 20Nm M10 BOULON = 40Nm M12 BOULON = 40Nm LÉGENDE...
  • Page 9 Page 9 of 9 FP0279 NOTICE DE MONTAGE Pour démarrer le montage, placez l'écrou Nyloc M8 (Article 7) sur l’extrémité M8 de la barre de • broche (article 3) et serrez jusqu'à ce qu'au moins 2 filets au moins traversent le Nyloc.