Publicité
Les langues disponibles
Les langues disponibles
in the air can be drawn into the equipment and cause
an accelerated rate of corrosion of some of the heater
components. The use of such chemical compounds near
the enclosure should be avoided.
IMPORTANT: If the building has a slight negative
pressure or contaminants are present in the air, an
outside combustion air supply to the heater is strong
recommended.
For an outside air supply a three (3") inch (7.62 cm) O.D.
single wall pipe may be attached to the heater. The duct
may be up to twenty five (25') feet (7.62 m) maximum
length or three (3') feet (0.91 m) minimum length with no
more than two (2) elbows.
VERTICAL THROUGH THE ROOF
3' (0.91 m)
Min.
Flashing
3" (7.62 cm)
Starting Collar
The air supply duct may have to be insulated to prevent
condensation on the outer surface. The outside air terminal
should be securely fastened to the outside wall by drilling
four (4) holes in the outside flange; wood screws or bolts
and expansion sleeves may be used to fasten terminal.
Outside Air
Terminal
3" (7.62 cm)
Flue Pipe
Seal All Joints
3" (7.62 cm)
Flue Pipe
Seal All Joints
Flex Pipe
6" to 12" long
Outside Air
(15.24 cm to 0.3 m)
Terminal
Wall
Vent Cap
(Leslie VersaCap)
4" (10.16 cm) Dia.
Single-Wall Pipe
6" Min.
(15.24 cm)
Intake
Vent
NOTE:
Flue pipe requires
Roof
additional support. Flex
pipe will not support riser
and outside air terminal.
Flex Pipe
6" to 12" long
(15.24 cm to 0.3 m)
Vertical Outside Air
Horizontal Outside
Air
L'Instruction Mettre A Eletrique
Cet appareil de chaffage est equipe ave une trios
(mettre a terre) le bouchon pour votre protedtion
contre le danger da choc et devrait etre directement
plugged dans un convenablement a mis a terre
receptacle de trios broche. N' pas couper ou enlever
la broche metrre a terre de ce bouchon.
Gas-Fired Low-Intensity Infrared Heater
Electrical Service Installation:
System Requirements
The GSP tube heater requires a grounded three-prong
electrical outlet to be installed within 36" (0.91 m) of the
rear surface of the heater's burner box. It is recommended
that the outlet for the heater be ceiling-mounted and
should be on a dedicated circuit. DO NOT use an electrical
extension cord to operate the heater.
In order to control the heater thermostatically, it is
necessary the grounded three-prong electrical outlet
be controlled with a on/off switch or a line voltage
thermostat. Please consult with an electrician or follow all
local electrical codes.
Heater Rating: 120VAC, 60Hz, Single Phase, 1 Amp
Low Voltage Thermostat Wiring Diagram
Heaters are normally controlled by thermostat. The
recommended 24V thermostat connects to the unit as
shown in the diagram below.
120V-60Hz
Supply Circuit
Grounding
The heater must be electrically grounded in accordance
with the following codes: United Stats: Refer to National
Electrical Code, ANSI/NFPA-70-latest revision. Wiring must
conform to the most current National Electrical Code and
local ordinances. Canada: Refer to Canadian Electrical
Code, CSA C22.1 Part 1-latest revision.
The appliance, when installed, must be electrically
grounded in accordance with local code, or in the absence
of local codes, with the National Electrical Code (ANSI/
NFPA 70) or Canadian Electrical Code (CSA 22.1), if an
external electrical source is utilized.
WARNING Electrical Shock Hazard:
Plug heater into grounded three prong ceiling
receptacle. Do not cut or remove the grounding
prong from this plug. Do not use with an extension
cord. Failure to follow these instructions will result in
death or electrical shock.
CAUTION: Label all wires prior to disconnection when
servicing controls. Wiring errors can cause improper
and dangerous operation. Verify proper operation
after servicing.
15
Operating Instructions and Owner's Manual
Heater (maximum 1-per thermostat)
Heater
Low Voltage
Thermostat
Stock # 10367
Electrical Grounding Instructions
This heater is equipped with a three-prong
(grounded) plug for your protection against shock
hazard and should be plugged directly into a
properly grounded three-prong receptacle. Do not
cut or remove the grounding prong from this plug.
Publicité
