F.F. Group CBBG 400 PLUS Notice Originale page 9

CBBG 400 PLUS
SERVICE
Have your power tool serviced by an autho-
rized service and use only original spare parts.
This will ensure that the safety of the power tool
is maintained.
BENCH GRINDER SAFETY WARNINGS
Do not use a damaged accessory. Before
f
each use, inspect the accessory such as
abrasive wheels for chips and cracks. After
inspecting and installing an accessory, posi-
tion yourself and bystanders away from the
plane of the rotating accessory and run the
power tool at maximum no-load speed for
one minute. Damaged accessories will normally
break apart during this test time.
The rated speed of the accessory must be at
f
least equal to the maximum speed marked
on the power tool. Accessories running faster
than their rated speed can break and fly apart.
Never grind on the sides of a grinding wheel.
f
Grinding on the side can cause the wheel to
break and fly apart.
Wear safety goggles.
f
Never leave the tool unattended before it
f
has come to a complete stop. Cutting tools
that are still running can cause injuries.
Store the power tool and accessories safely
f
when it is not in use. The storage location
must be dry and lockable. This prevents the
power tool from storage damage, and from be-
ing operated by untrained persons.
Check the cable regularly and have a dam-
f
aged cable repaired only by an authorised
customer service agent for FF Group power
tools. Replace damaged extension cables.
This will ensure that the safety of the power tool
is maintained.
Connect the tool to a mains supply that is
f
properly connected to earth. The socket and
extension cable must have a fully functioning
protective conductor.
Keep your work area clean. Material mixtures
f
are particularly hazardous. Light metal dust may
catch fire or explode.
Protect the grinding tool against impact,
f
shock and grease.
CONNECTION TO THE POWER SUPPLY
Make sure the power supply information on the
machine's rating plate are compatible with the
power supply you intend to connect it to.
This appliance is Class I* and is designed for
connection to a power supply matching that
detailed on the rating label and compatible with
the plug fitted. If an extension lead is required,
use an approved and compatible lead rated for
this appliance. Follow all the instruction sup-
plied with the extension lead.
PRODUCT SPECIFICATIONS
INTENDED USE
The power tool is intended for sharpening tools
and for grinding and deburring metal. The power
tool may only be operated for short periods (max.
60 mins).
TECHNICAL DATA
Article number
Model
Voltage/Frequency
Rated power
(S2:10 min)
Rated power (S1)
No Load Speed
Dry wheel size Left
Grit
Disc Speed
Belt Size
Grit
Weight
Sound emission values
Typically the A-weighted noise levels of the product
are:
Sound pressure level
Sound power level
Uncertainty K
WEAR HEARING PROTECTION
The noise emission value given in these instructions
has been measured in accordance with a stan-
dardised measuring procedure and may be used to
compare power tools. It may also be used for a pre-
liminary estimation of noise emissions.
The noise emission value given represents the main
applications of the power tool. However, if the pow-
er tool is used for other applications, with different
application tools or is poorly maintained, the noise
emission value may differ. This may significantly
increase noise emissions over the total working
period.
To estimate noise emissions accurately, the times
when the tool is switched off, or when it is running
but not actually being used, should also be taken
into account. This may significantly reduce noise
emissions over the total working period.
IDENTIFICATION
1. Led work light
2. Sanding belt
3. Work table deflector
4. ON/OFF switch
5. Tool rest
6. Grinding wheel
7. Eyeshield assy
8. Spark guard
English | 9
45 524
CBBG 400
PLUS
V 230
Hz 50
W 400
W 250
min 2.980
-1
mm 150 x 20 x 12,7
# 36
min 2.980
-1
mm 50 x 686
# 80
kg 8,3
dB(A) 85,3
dB(A) 91,8
dB 3,0
www.ffgroup-tools.com