Maytag Performance Serie Guide D'utilisation Et D'entretien page 7

Select the correct cycle and dryness [eve[ or temperature for your
load. If a Sensor Cycle is running, the display shows the estimated
cycle time when your dryer is automatically sensing the dryness
[eve[ of your load. If a Timed Cycle is running, the display shows the
exact number of minutes remaining in the cycle.
Coo[ Down tumbles the load without heat during the last few
minutes of all cycles. Coo[ Down makes the loads easier to handle
and reduces wrinkling. The length of the Coo[ Down depends on the
load size and dryness [eve[.
Drying tips
• Follow care label directions when they are available.
If desired, add a fabric softener sheet. Follow package
instructions.
Remove the load from the dryer as soon as tumbling stops to
reduce wrinkling. This is especially important for permanent
press, knits, and synthetic fabrics.
Avoid drying heavy work clothes with lighter fabrics. This could
cause overdrying of lighter fabrics, leading to increased
shrinking or wrinkling.
If you dry sheets in a mixed load or large items, rearrange the
load when the signal sounds. This will aid in the drying process.
Cycle tips
• Dry most loads using the preset cycle settings.
• Refer to the Sensor or Timed Preset Cycle Settings chart (in the
"Cycles" section) for a guide to drying various loads.
• I)rying temperature and Sensor Cycles I)ryness are preset to
Normal when you choose a Sensor Cycle and will dry most
loads adequately using the most efficient amount of energy.
You can choose a different dryness level, depending on your
load by pressing the SENSOR CYCI_ES DRYNESS button to
select More Dry, Normal, or I.ess Dry.
• If you wish to adjust the cycle length of a Timed Cycle, you
must press the TIME ADJUST up or down buttons. Adjust the
temperature of a Timed Cycle by pressing, TIMED CYCI.ES
TEMP until the desired temperature is selected.
NOTE: You cannot choose a Sensor Cycles Dryness with
Timed, Steam, or Sanitize Cycles. Some cycles are not
available on all models.
NOTE: Not all cycles available on all models.
Select the drying cycle that matches the type of load you are drying.
See Sensor Preset or Manual Preset Cycle Settings chart.
Steam Models
nerma[ super delicate
bulky
items
casual !
sensor c_les
sanitize
timed _ )id refresh
timed dry
quick dry :ustom refresh
check lint screen
Non-Steam Model
norma!
casual
sensor cycles
timed c'
timed dr_
quick dry
super delicate
delicate
check lint screen
Cycle Control knobs
Sensor Cycles
Sensor Cycles allow you to match the cycle to the load you are
drying. See the following Sensor Cycle Settings chart. Each cycle
dries certain fabrics at the recommended temperature. A sensor
detects the moisture in the load and automatically adjusts the drying
time for optimal drying.
Sanitize (on some models)
Use this cycle for items such as towels, bedding, children's clothing,
or other items needing to be sanitized. This cycle is designed to
eliminate 99.9% of 3 common infectious bacteria. This cycle should
be run to completion to ensure sanitization. For best results, do not
interrupt cycle.
NSF Protocol P154
Sanitization Performance of
Residential clothes Dryers
Sensor Cycle Settings
Sensor Cycles Temperature Time*
Load Type (Minutes)
SANITIZE High 60
Towels, bedding, children's
clothing
HEAVY DUTY High 50
Heavyweight items, towels, jeans
BULKY ITEMS Regular 55
Jackets, comforters, pillows
NORMAL Regular 40
Permanent press blends, work
clothes, sheets
CASUAL Medium 35
Permanent press, synthetics
DELICATE Medium 30
I.ingerie, blouses, washable knit
fabrics
SUPER DELICATE I.ow 25
I.ingerie, exercise wear, washable
woolens
*Estimated Time with Sensor Cycles Dryness (Normal) setting. Time
will vary depending on load type and load size.