Location Requirements; Opening Dimensions - Jenn-Air W11231557A Instructions D'installation

Location Requirements

Keep ammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or re.
IMPORTANT:
Observe all governing codes and ordinances.
■
It is recommended that you do not install the refrigerator near
■
an oven, radiator, or other heat source.
Do not install in a location where the temperature will fall
■
below 55°F (13°C).
Floor must support the refrigerator weight, more than 600 lbs
■
(272 kg), door panels, and contents of the refrigerator.
Each refrigerator needs to be installed in a separate cabinet
■
frame.

Opening Dimensions

This refrigerator is designed to be installed inside a frame that ts
between kitchen cabinets. The inside of the frame should be a
minimum of 69 / " (177.6 cm) high, 22¹⁄
15
16
21 ⁄ " (55.5 cm) deep (front to back).
7
8
For proper ventilation, you must allow adequate unobstructed
space behind the refrigerator and below and above the frame.
Air enters below the refrigerator and exits above it.
Allow a clearance minimum of 2" (50 mm) at the top of the
■
frame.
The minimum depth of the base of the frame is 20
■
(520 mm) (front to back).
The base can be as desired, but height should match height
■
of toe kick of surrounding cabinets. A vent with an opening
of at least 31 sq in. (200 sq. cm) is required for proper
ventilation.
If the space between the top of the frame and the ceiling
■
is open air, allow a minimum of 7
refrigerator.
If the space between the top of the frame and the ceiling is
■
enclosed as part of the surrounding cabinetry, a vent with an
opening of at least 31 sq. in. (200 sq. cm) is required.
4
09-Mar-2018 14:10:27 EST | RELEASED
WARNING
Explosion Hazard
" (56.0 cm) wide, and
16
⁄ " (200 mm) above the
7
8
In some European factories the letter "W" of the part code mentioned herein will be automatically
The bottom of the vent must be a minimum of 7
above the refrigerator.
NOTE: Vent covers are not supplied with the unit.
A
Dimension Table
A
B
C
D
E
F
G
H
⁄ "
1
2 I
J
K
L
M
N
O
replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")
/ "
1
8
(4 mm)
E
F
B
H
G
C
D
I
F
69 ⁄ " (177.6 cm)
15
16
22 ⁄ " (56.0 cm)
1
16
minimum 21 ⁄ " (555 mm)
7
8
minimum 20 ⁄ " (520 mm)
7
16
minimum 2" min. (50 mm)
69 ⁄ " (177.0 cm)
11
16
21 / " (54.0 cm)
9
32
21 / " (54.5 cm)
15
32
2 / " (60 mm)
3
8
1/16" (2 mm)
20 / " (105.75 cm)
5
8
3/16" (10 mm)
28" (71 cm)
26 / " (66.85 cm)
5
16
1 ⁄ " (30 mm)
1
8
" (20.0 cm)
7⁄
8
/ "
3
8
(9 mm)
/ "
1
16
(2 mm)
J
K
L
N M
O