Publicité
Les langues disponibles
Les langues disponibles
• Disconnect the suction hose from the skimmer inlet. Loosen the clamp that secures the hose and hold the hose so
that no water leaks and submerge immediately in the pool so that it remains primed.
• Weigh down the end of the this hose with a heavy object which cannot damage the liner so that it is forced to sink to
the bottom of the pool.
• Start up the pump and drain the pool. Remember that the filter will not fully drain the pool. When a few cm. of water
are left and the pump no longer sucks in water, shut it off.
• Once the pump to drain the pool is on, do not stop the process until it is finished, to ensure that it does not become
unprimed.
• If you are going to refill the pool with water, first remove the remaining water by hand without damaging the liner.
• If you are going to disassemble the pool, you can fold the liner with the remaining water in the centre.
• Remove the plate in the DREAM POOL model or the tubes in the JET POOL model.
• Unfold the liner in order to drain it fully.
• This operation should not be performed except to disassemble the pool.
THE HOSE SHOULD NOT CONTINUE SUCTIONING THE BOTTOM OF THE POOL LINER. THE PUMP MAY BE
SERIOUSLY DAMAGED IF IT OPERATES WITHOUT WATER CIRCULATION. THE LINER MAY ALSO BE
6 MAINTENANCE
After the bathing season has ended, the filter should be kept in a dry place where it is protected from inclement weather.
For this purpose, after performing a final backwash to clean the silica sand, dismount the hoses and drain the water in the
filter through the tank drain plug until it is completely empty.
After removing all of the water from the filter, carefully clean the remains of silica sand from the thread before replacing
the plug. Failure to do so could damage the thread.
The filter tank drain plug should only be used in this operation.
After stoppage for an extended period, it is also recommendable to make sure that the filter is primed before starting up.
Troubleshooting and technical service
This filter and its instructions are designed for domestic use, with no need for professional supervision, except for
exceptional cases. Here we shall describe the problems and causes which may arise after years of service of the filter
that you can repair yourself. If you cannot solve the problem, contact the pool manufacturer at the telephone indicated in
the instructions.
PROBLEM
The filter leaks through the hose terminals
After the filter has started up, there is no flow in
the feedback nozzle.
Intermittent operation
The flow rate of the filter is low.
Water comes out through the filter opening.
The filter valve leaks through the drain terminal.
The motor will not start up. There is no noise or
vibration.
The motor does not start up but a buzzing sound
can be heard.
Water leakage.
DAMAGED BECAUSE OF SUCTION.
CAUSE
Improper connection between the terminals and
the hoses.
The valve is not on the filtration setting.
The filter is above the level of the unprimed
water.
The suction cover or the skimmer plug have
been inserted.
Low water level on skimmer
The filter is not primed.
Due to use, the filter is dirty.
The filter is not primed.
The connection between the valve and the filter
is dirty.
Plasticl band is loose.
Inner coupling damaged due to improper use of
chemical product.
Valve head broken due to improper use.
(overtightening)
No current in the electric line.
Motor damaged
Find out where the water is leaking.
11
SOLUTION
Place Teflon in the housings. Insert the hose
terminals up until the bottom of the housing and
tighten the clamps.
Disconnect the filter and place the valve on the
correct setting.
Place the filter in the correct position and prime
it.
Remove the suction cover or the skimmer plug.
Fill the pool and prime the filter.
Prime the filter.
Perform a backwash.
Prime the filter.
Clean the sand from the opening. Insert the
coupling on the valve properly and tighten the
plastic band firmly.
Change the top valve cover.
Do not put chemical products in the preliminary
filtration skimmer basket.
Change the valve head. Do not overtighten.
Check that there is current in the electric line.
Contact the After-Sales Service of the pool
manufacturer.
Check the hose clamps.
If the leak is between the pump and the motor,
contact the After-Sales Service of the pool
manufacturer.
Publicité
