R&G SS0050 Notice De Montage page 2

Masquer les pouces

page de 2

/ 2
Signets

ARTICLE 3 = AXE (SB110) (x1)

ARTICLE 4 = M6 ÉCROUS (x2)

ARTICLE 5 = M6 RONDELLES (x2)

Page | 4

NOTICE DE MONTAGE



Positionner une rondelle M6 (article 5) et un écrou M6 (article 4) sur l'extrémité filetée de l'axe (article 3).

Veiller à ce que l'écrou soit complètement engage sur le filetage.



Placer la bobine du côté gauche (article 1) sur l'axe, de façon à ce que l'écrou et la rondelle se placent dans le

contre alésage de la bobine, puis positionnez la dans le moyeu arrière depuis le côté gauche de la moto, en

veillant à ce que la bobine se place dans le trou du moyeu d'origine.



L'axe devrait maintenant dépasser du côté droit de la roue arrière. Placer la bobine restante (article 2) sur

l'extrémité de la bobine, en veillant à ce que la bobine se place dans la roue.



Insérer la rondelle restante et l'écrou sur le filetage exposé de l'axe de moyeu puis serrer.



Veiller à ce que l'ensemble corresponde au schéma présent en page 1. Serrer complètement les écrous des 2

cotés. Ne pas trop serrer – les écrous fixent l'ensemble.

The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not

diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or

warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it

has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other

services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is

responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G

shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or

maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident

or neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for

indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service

concerned. These terms do not affect the Buyer's statutory rights.

Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct

from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of

R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The

customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your

statutory rights and does not refer to faulty goods.

Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301

OUTILS REQUIS



Clé à cliquet + douilles 10mm (x2).

VALEURS DE SERRAGE RECOMMANDÉES



M5 BOULON = 12Nm



M6 BOULON = 15Nm



M8 BOULON = 20Nm