Publicité
Les langues disponibles
Les langues disponibles
English
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to be recharged.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature
is between 65 °F – 75 °F (18 ° C– 24 °C). DO NOT charge
when the battery pack is below 40 °F (4.5 °C), or above
104 °F (40 °C). This is important and will prevent serious
damage to the battery pack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger from
the AC outlet before cleaning. Dirt and grease may be
removed from the exterior of the charger using a cloth
or soft non-metallic brush. Do not use water or any
cleaning solutions.
Wall Mounting
Some D
WALT chargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
8
Attaching Water Outlet Fixing (Fig. D)
1. To attach the water outlet fixing
the hose connector plate
3
outlet
.
2. Slide the water outlet fixing screws
fasten securely.
3. Screw the water outlet fixing nut
outlet securely.
Attaching and Removing Nozzle (Fig. E)
1. Screw the nozzle connector
8
2. Slide the nozzle
straight into the hose connector until
it snaps into place.
3. To remove the nozzle, pull back on the nozzle connector
9
release collar
until the nozzle pops out.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
WARNING: Never direct water stream toward face or
eyes of people or pets or any electrical device. Failure
to follow this instruction could lead to injury, electrical
shock or death.
Installing and Removing the Battery Pack
(Fig. F)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
nOTE: For best results, make sure your battery pack
fully charged.
•
To install the battery pack into the tool
1. Press the battery compartment release button
2. Lift the battery compartment cover
3. Align the battery pack with the rails inside the
battery compartment and slide it in until the battery
pack is firmly seated in the tool, and ensure it does
not disengage.
4. Close the battery compartment cover. Ensure the battery
compartment release button clicks into place.
•
To remove the battery pack:
1. Press the battery compartment release button.
2. Lift the battery compartment cover.
3. Press the battery pack release button
pull the battery pack out of the water tank. Insert it
into the charger as described in the charger section of
this manual.
4. Close the battery compartment cover. Ensure the battery
compartment release button clicks into place.
To Fill Tank (Fig. G)
WARNING: Use care in filling water tank. Do not
overflow. Keep water away from battery and internal
electrical components to avoid damage.
14
1. Unscrew the tank cap
1
, line up the holes of
2
with the holes of the water
4
through and
5
onto the water
6
to the end of the hose
11
12
.
13
and firmly
15
and ensure the filter
is in place.
7
.
10
is
.
Publicité
