Makita CE003G Manuel D'instructions page 14

ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing the abrasive
cut-off wheel / diamond wheel
CAUTION:
Use only the Makita wrench to
install or remove the wheel.
CAUTION:
When installing the wheel, be sure
to tighten the bolt securely.
CAUTION:
Do not press the shaft lock button
when the wheel is rotating.
NOTICE:
Do not use wheels that are severely
damaged, worn, or whose expiration date has
passed. Malfunction, abnormal noise, or breakage
may occur.
To remove the wheel, press the shaft lock button and
rotate the wheel until the wheel cannot revolve. While
the shaft lock is fully locked, turn the hex bolt counter-
clockwise using the box wrench. Then remove the hex
bolt, outer flange and wheel.
► Fig.8: 1. Shaft lock button 2. Box wrench 3. Tighten
4. Loosen
► Fig.9: 1. Hex bolt 2. Outer flange (black) 3. Abrasive
cut-off wheel / diamond wheel 4. Inner flange
(silver) 5. Arrow (rotation direction of the
wheel)
To install the wheel, follow the removal procedure in
reverse.
BE SURE TO TIGHTEN THE HEX BOLT SECURELY.
CAUTION:
Always install the wheel so that
the arrow on it points in the same direction as the
arrow on the wheel guard. Otherwise, the wheel
rotates in reverse, which may cause personal injury.
CAUTION:
Only use a wheel that is marked
with a speed equal to or higher than the speed
marked on the tool.
NOTE: If an inner flange is removed by chance,
install the inner flange so that taller protrusion faces
the tool side as shown in the figure.
CE003G (for the abrasive cut-off wheel / diamond
wheel)
► Fig.10: 1. Hex bolt 2. Outer flange 46 (black)
3. Abrasive cut-off wheel / diamond wheel
4. Inner flange 46 (silver) 5. Protrusion
(taller)
CE004G (for the diamond wheel)
► Fig.11: 1. Hex bolt 2. Flange 50 (black) 3. Ring
4. Diamond wheel
CE004G (for the abrasive cut-off wheel)
► Fig.12: 1. Hex bolt 2. Flange 80 (black) 3. Ring
4. Abrasive cut-off wheel
Connecting to water supply
1. Prepare a water hose.
2. Remove the nut on the coupling sleeve and pass
the water hose through the nut. Insert the end of the
hose into the coupling sleeve and then tighten the nut.
► Fig.13: 1. Water hose 2. Nut of the coupling sleeve
3. Coupling sleeve
3. Connect the water hose to the water supply.
When connecting to a water faucet, use a suitable fitting
such as hose band or water tap joint.
► Fig.14: 1. Hose band 2. Water tap joint 3. Water
hose
NOTE: The fitting depends on the shape of the faucet
to which you connect. Prepare a suitable commercial-
ly-bought fitting.
NOTE: If you use a water tap joint, prepare another
coupling sleeve and attach it to the other end of the
hose.
NOTE: When using a water pump, follow the instruc-
tions of your water pump to connect the water hose.
4. Push the coupling sleeve into the water inlet until it
locks with a click.
► Fig.15: 1. Coupling sleeve 2. Water inlet 3. Cock
NOTICE:
Keep the cock closed until you start the
cutting operation with water feeding. For how to
feed water, refer to the section for the operation.
OPERATION
CAUTION:
Be sure to hold the workpiece
firmly down on a stable bench or table during
operation.
CAUTION:
Do not twist or force the tool in the
cut, or else the motor may be overloaded or the
workpiece may break.
CAUTION:
Do not touch the wheel or work-
piece immediately after operation, as they may
become hot and may cause burns.
Cutting
CAUTION:
During operation, do not bring the
tool higher than your shoulder height.
► Fig.16
Hold the tool firmly. Grasp the handle with your right
hand and the grip with your left hand. To prevent electric
shock by accidental cutting of an electric cable, always
hold the grip by the designated portion as shown in the
figure.
► Fig.17: 1. Part to hold
Move the tool over the workpiece surface, keeping it
flat and advancing smoothly until the cutting is com-
pleted. Keep your cutting line straight and your speed of
advance uniform.
► Fig.18
14 ENGLISH