Publicité
Les langues disponibles
Les langues disponibles
Warning! This saw is equipped with a removable
stop rail (48) which is screwed to the fi xed stop
rail (13).
To make 0°-45° miter cuts to the right (with the
machine head (4) inclined or with the turntable
set at an angle), the removable stop rail (48) must
be completely removed. Warning! In this case the
maximum permissible workpiece height is redu-
ced (see 4. Technical data).
•
Undo the grub screw (49) of the removable
stop rail (48) with a hexagon key (see Fig. 19).
Note: There is no 4 mm hex key included in
the scope of this delivery
•
Pull off the removable stop rail in upwards
direction.
•
Always fasten the removable stop rail (48) on
the equipment again after you have comple-
ted your work.
•
The stop rail must always be kept together
with the equipment. A removed stop rail will
impair the operational safety of the equip-
ment.
6.1 Cross cut 90° and turntable 0° (Fig. 1-3,
11)
For cutting widths up to approx. 100 mm it is
possible to fi x the saw's drag function with the
locking screw for drag guide (29) in rear position.
If the cutting width exceeds 100 mm you must
ensure that the locking screw for drag guide (29)
is slackened and that the machine head (4) can
be moved.
•
Move the machine head (4) to its upper po-
sition.
•
Use the handle (1) to push back the machine
head (4) and fix it in this position if required
(dependent on the cutting width).
•
Place the piece of wood to be cut at the stop
rail (13) and on the turntable (19).
•
Lock the material with the clamping device
(8) on the fixed saw table (18) to prevent the
material from moving during the cutting ope-
ration.
•
Press the release button (3) to release the
On/Off switch (2).
•
Press the On/Off switch (2) to start the motor.
•
With the drag guide fixed in place: Use the
handle (1) to move the machine head (4)
steadily and with light pressure downwards
until the saw blade (7) has completely cut
through the workpiece.
•
With the drag guide not fixed in place: Pull the
machine head (4) all the way to the front and
then use the handle (1) to move it downwards
steadily and with light pressure. Now push the
Anl_TE_SM_254_Dual_SPK9.indb 31
Anl_TE_SM_254_Dual_SPK9.indb 31
GB
machine head (4) slowly and steadily to the
very back until the saw blade (7) has comple-
tely cut through the workpiece.
•
When the cutting operation is completed,
move the machine head (4) back to its upper
(home) position and release the On/Off but-
ton (2).
Important! The integral resetting springs will
automatically lift the machine head. Do not simply
let go of the handle (1) after cutting, but allow the
machine head (4) to rise slowly, applying slight
counter pressure as it does so.
6.2 Cross cut 90° and turntable 0° - 45°
(Fig. 1-3, 12)
The crosscut saw can be used to make crosscuts
of 0°- 45° to the left and 0° - 45° to the right in re-
lation to the stop rail.
•
Swing up the machine head (4).
•
Move the locking lever (20) to its top position
to enable the turntable to be adjusted.
•
While holding the release button (21) pressed
down, turn the turntable (19) and scale poin-
ter (22) to the desired angular setting on the
scale (23).
•
To lock the turntable (19), press the locking
lever (20) down.
•
Cut as described in section 6.1.
6.3 Miter cut 0°- 45° and turntable 0° (Fig. 1-3,
13)
The crosscut saw can be used to make miter cuts
to the left of 0°-45° and to the right of 0°-45° in
relation to the work surface.
•
If required, dismantle the clamping device (8)
or mount it on the opposite side of the fixed
saw table (18).
•
Move the machine head (4) to its upper po-
sition.
•
Fasten the turntable (19) in 0° position.
•
Move the locking grip (26) to its upper posi-
tion.
•
For a miter angle to the left: Tilt the machine
head (4) to the left until it coincides with the
required angular setting of the scale pointer
(24) on the scale (25).
•
For a miter angle to the right: Tilt the machine
head (4) approx. 10° to the left, press and
hold the release lever (9), swing the machine
head (4) over the 0° line to the right, after ap-
prox. 10° let go of the release lever (9), tilt the
machine head (4) to the right until it coincides
with the required angular setting of the pointer
(24) on the scale (25).
•
Then secure the locking grip (26) again.
- 31 -
02.08.2019 09:12:47
02.08.2019 09:12:47
Publicité
