EINHELL 43.008.75 Instructions D'origine page 30

locking screw (29).
5.4 Precision adjustment of the stop rail
(Fig. 6, 7)
•
Lower the machine head (4) and fasten in
place with the retaining pin (30).
•
Fasten the turntable (19) in 0° position.
•
Place the 90° stop angle (a) between the bla-
de (7) and the stop rail (13).
•
Slacken the four adjustment screws (44)
using a hex key, set the stop rail (13) to 90° in
relation to the saw blade (7) and retighten the
adjustment screws (44).
•
The angle stop (a) and hex key (5 mm) are
not included in the scope of this delivery.
5.5 Precision adjustment of the angle stop for
crosscut 90° (Fig. 8a, 9)
•
Lower the machine head (4) and fasten in
place with the retaining pin (30).
•
Fasten the turntable (19) in 0° position.
•
Undo the locking grip (26) and tilt the machi-
ne head (4) to 0° using the handle (1).
•
Place the 90° angular stop (a) between the
blade (7) and the turntable (19).
•
Slacken the lock nut (37) and adjust the ad-
justment screw (35) until the angle between
the blade (7) and the turntable (19) equals
90°.
•
Retighten the lock nut (37) to secure this
setting.
•
Finally, check the position of the pointer (24).
If necessary, release the pointer with a cros-
stip screwdriver, move to the 0° position of the
angle scale (25) and retighten the pointer.
•
The angle stop (a) and crosstip screwdriver
are not included in the scope of this delivery.
5.6 Precision adjustment of the angle stop for
45° miter cut to the left (Fig. 8b, 10a)
•
Lower the machine head (4) and fasten in
place with the retaining pin (30).
•
Fasten the turntable (19) in 0° position.
•
Undo the locking grip (26) and tilt the machi-
ne head (4) all the way to the left to 45° using
the handle (1).
•
Place the 45° stop angle (b) between the bla-
de (7) and the turntable (19).
•
Slacken the lock nut (37) and adjust the ad-
justment screw (36) until the angle between
the blade (7) and the turntable (19) equals
exactly 45°.
•
Retighten the lock nut to secure this setting.
•
No angle stop (b) included.
Anl_TE_SM_254_Dual_SPK9.indb 30 Anl_TE_SM_254_Dual_SPK9.indb 30
GB
5.7 Precision adjustment of the angle stop for
45° miter cut to the right (Fig. 8b, 10b)
•
Lower the machine head (4) and fasten in
place with the retaining pin (30).
•
Fasten the turntable (19) in 0° position.
•
Undo the locking grip (26) and tilt the machi-
ne head (4) all the way to the left to 45° using
the handle (1).
•
Place the 45° stop angle (b) between the bla-
de (7) and the turntable (19).
•
Slacken the lock nut (37) and adjust the ad-
justment screw (47) until the angle between
the blade (7) and the turntable (19) equals
exactly 45°.
•
Retighten the lock nut to secure this setting.
•
No angle stop (b) included.
6. Operation
Warning! To make 90° crosscuts, the adjustable
stop rail (14) must be fi xed at the inner position:
•
Undo the locking grip (15) for the adjustable
stop rail and push the adjustable stop rail
inwards.
•
The adjustable stop rail (14) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (14) and
the saw blade (7) amounts to a maximum of
8mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking grip (15) again.
Warning! To make 0°-45° miter cuts to the left
(with the machine head (4) inclined or with the
turntable set at an angle), the adjustable stop rail
(14) must be fi xed at an outer position.
•
Undo the locking grip (15) for the adjustable
stop rail and push the adjustable stop rail
outwards.
•
The adjustable stop rail (14) must be fixed far
enough in front of the innermost position that
the distance between the stop rail (14) and
the saw blade (7) amounts to a maximum of
8mm.
•
Before making a cut, check that the stop rail
and the saw blade cannot collide.
•
Tighten the locking grip (15) again.
- 30 -
02.08.2019 09:12:47 02.08.2019 09:12:47