Troubleshooting Measures; Declaration Of Conformity - Birchmeier Indu-Matic 20 M Mode D'emploi

Troubleshooting measures

Cause
Decay of pressure in tank
Manometer, hoses not tightened down firmly
or seals defective.
Hose torn or perforated
Tank defective or strongly dented
Pistol valve dirty
Pistol valve leaking
Nozzle spray irregular
Nozzle clogged.
Nozzle bore eroded.
Spare parts and repairs
If any part shows signs of damage or wear, replace it immediately. Use only BIRCHMEIER original parts (see spare
parts list).
Guarantee
• Prerequisite to the honoring of warranties is the appropriate storage and use of our equipment strictly in
accordance with the operating instructions which were valid on delivery (including the instructions given on the
appliances themselves). These instructions constitute an integral part of our contract. Any and all damages which
fall within our scope of responsibility must be reported to us in writing immediately after they have been
discovered.
• Expressly excluded from the warranty and liability are damages and deficiencies:
• Resulting from the non-adherence to our instructions and usage recommendations in the operating manuals such
as the improper use or inadequate maintenance of our equipment;
• Resulting from chemical attack, or due to normal wear;
• Due to damages, the causes of which are beyond the scope of our responsibility and influence, e.g. mechanical
damage, force majeure.
• The warranty becomes null and void and any and all liabilities are disclaimed if the user or any third party alters or
makes inexpert repairs to the sprayer.
• Excluded from the warranty and liability are all incidents which extend beyond the obligations set forth above. Any
and all liability is expressly excluded to the extent of the law. Expressly excluded is in particular any and all liability
for damages which are purely asset-related such as lost profit, loss of use, operating outage etc.
Place of jurisdiction: Baden, Switzerland
Applicable law: Swiss law
For any further information concerning use or maintenance of the equipment please refer to your dealer.
Remedy
Tighten down pressure gauge (14) and
hoses (21) or change defective seals.
Change hose.
Change tank.
Repair work is prohibited.
Detach pistol valve (22), clean thoroughly,
grease valve rod and reassemble.
Change pistol valve (22).
Clean nozzle (26).
Change nozzle (26).
Technical data
Indu-Matic 20 M / 50M / 100M
Admissible operating pressure max. 6 bar
Admissible operating temperature 5° - 50°C (41°F - 122°F)
Spraying rate - Regulating valve A
1.5 rotations Approx. 0.4 ltr./min.
2.5 rotations Approx. 0.7 ltr./min.
4.0 rotations Approx. 1.1 ltr./min.
Filling capacity 20 ltr. / 45 ltr. / 90 ltr.
Total capacity 23.5 ltr. / 50 ltr. / 100 ltr.
Weight 23 kg / approx. 66 kg / approx. 123 kg

Declaration of Conformity

on Manufacturing and Approval for Pressure Vessels in according to Directive 2014/68/EU
Article number:
Indu-Matic 20 M: 115 618 01
Indu-Matic 50 M: 116 648 01
Indu-Matic 100 M: 116 648 02
Manufacturer:
Birchmeier Sprühtechnik AG, CH-5608 Stetten
Conformity assessment
procedure: Module A2 (category II, fluids in group 1)
Apparatus
Condition of fluid
Max allowable pressure PS
Max allowable temperature TS
Min allowable temperature TS
Volume V
Test-pressure PT
Capacity of filling
Apparatus
Point of application
Peculiarity
Regulations followed
Marked
Safety control equipment
We declare, that the described equipment is in compliance with the Directive 2014/68/EU of the European Parliament
and of the Council of 15. May 2014.
The declaration is based on the EU-Certificate of conformity:
Internal production control plus supervised pressure equipment checks according to Module A2.
Advises for operators are in the operating manual.
Stetten, 22.04.2020
M. Zaugg
Head of Development & Construction
20 M 50 M 100 M
Air Air Air
6 bar 6 bar 6 bar
50°C 50°C 50°C
5°C 5°C 5°C
23.5 l 50 l 100 l
6.6 bar 6.6 bar 6.6 bar
20 l 45 l 95 l
20 M / 50 M / 100 M
Foam sprayer
mobile
AD 2000
CE 1253
with safety valve