EINHELL TE-MB 18/127 Li Mode D'emploi page 15

vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).
5. Before starting the equipment
Warning!
Always remove the battery before making
adjustments to the machine.
5.1 General information
•
Warning! Before you use the machine for the
first time, tension the blade (13) (see 5.5).
•
All covers and safety devices must be
properly fitted before the machine is switched
on.
•
It must be possible for the blade to run freely.
•
Before you actuate the On/Off switch, make
sure that the blade is correctly fitted and that
the machine's moving parts run smoothly.
•
Important! The two hex. keys (20/21) are
stored in the adjustable handle (8) (see Fig.
3).
•
Important! Please note that the tooth pitch
of the blade you are using must match the
material you want to cut. In the case of
particularly hard materials or particularly
large depths of blade penetration you should
change the tooth pitch by changing the blade.
5.2 Adjusting the handle (Fig. 4-7)
•
The adjustable handle (8) can be fastened
in various locking positions according to
requirements.
•
Release the clamping lever (9).
•
Place the adjustable handle (8) in the
required position.
•
Lock the setting by refastening the clamping
lever (9).
•
Important! You can adjust the pretension of
the clamping lever (9). To do so, hold the
released clamping lever (9) firmly and adjust
the nut (10) on the opposite side (clockwise:
higher tension). Check the setting by closing
the clamping lever (9) again. Keep repeating
until you have the required tension.
Anl_TE_MB_18_127_Li_SPK7_NA.indb 15 Anl_TE_MB_18_127_Li_SPK7_NA.indb 15
EN
5.3 Adjusting the workpiece stop (Fig. 8)
•
Important! The workpiece stop (11) is set at
the factory to bottom position.
•
Caution! When you use the cordless bandsaw
together with the optional miter stand, the
workpiece stop (11) must be set to bottom
position.
•
Caution! When you work without the optional
miter stand, the workpiece stop (11) should
also be set to bottom position because this
will increase the size of the guide face. Set
the workpiece stop to a higher position only in
exceptional cases.
•
Slacken the two socket head screws (12)
with the hex. key (20) in order to be able to
push the workpiece stop (11) to the required
position. Then retighten the two socket head
screws (12).
5.4 Information about the LED lamp (Fig. 1)
•
The machine has an LED lamp (4) for
illuminating the cutting area.
•
As soon as you press the On/Off switch (3),
the LED lamp (4) will come on automatically.
•
A few seconds after you release the On/Off
switch (3) again, the LED lamp (4) will switch
off automatically.
5.5 Fitting/removing the blade (Fig. 9-18)
Warning!
Before you start to fi t or remove the blade:
Remove the battery!
To prevent injury: wear gloves when changing
the blade!
Fitting:
•
To be able to remove the left-hand blade
cover (22), slacken the socket head screw
(26). With the latching hook (23) pushed and
held in the up position, slide the blade cover
(22) outwards.
•
To be able to remove the right-hand blade
cover (24), slacken the socket head screw
(26). With the latching hook (25) pushed and
held in the up position, slide the blade cover
(24) outwards.
•
Before you mount the new blade, clean the
guide rollers (18) and the two blade pulleys
(16). Make sure in particular that the rubber
tire (17) is free of chips.
•
Caution! A damaged rubber tire (17) must be
replaced immediately.
•
To be able to fit the blade you must open the
clamping mechanism for the blade. Open the
- 15 -
28.02.2024 10:43:51 28.02.2024 10:43:51