Publicité
Les langues disponibles
Les langues disponibles
industrial applications. Our warranty will be voided
if the equipment is used in commercial, trade or
industrial businesses or for equivalent purposes.
General safety information
It is the user's responsibility to install and use
the machine properly in accordance with the
instructions issued by the manufacturer. If
electromagnetic interference is noticed, it is the
user's responsibility to eliminate said interference
with the technical devices mentioned in the
section "Important information about the power
connection".
Only blades suitable for the machine are allowed
to be used. To use the machine properly you must
also observe the safety information, the assembly
instructions and the operating instructions to be
found in these operating instructions.
All persons who operate and service the machine
must be acquainted with these instructions
and must be informed about potential hazards.
It is also imperative to observe the accident
prevention regulations in force in your area. The
same applies for the general rules of health and
safety at work.
The manufacturer will not be liable for any
changes made to the machine nor for any
damage resulting from such changes.
Even when the machine is used as prescribed
it is still impossible to eliminate certain residual
risk factors. The following hazards might arise in
connection with the machine's construction and
design:
•
Damage to hearing if essential ear protection
is not used.
•
Harmful emissions of wood dust when used
in closed rooms.
•
Risk of accident through hand contact with
the blade in the uncovered cutting zone.
•
Risk of injury when changing the blade (risk
of cuts).
•
Injuries from catapulted workpieces or parts
of workpieces.
•
Crushed fingers.
•
Injuries from kickback.
•
Tilting of the workpiece due to inadequate
support.
•
Touching the blade.
•
Dust and splinters can cause eye injuries.
For this reason, you must always wear safety
goggles or glasses with safety lenses.
•
Dust presents a special danger. You should
Anl_TE_MB_18_127_Li_SPK7_NA.indb 14
Anl_TE_MB_18_127_Li_SPK7_NA.indb 14
EN
wear a suitable safety mask so that you are
not forced to breathe in any dust.
•
Always wear tight-fitting protective clothing
that is in perfect condition.
•
Long hair must be tied together, loose jewelry
should not be worn.
•
The workpiece you want to cut must always
be clamped securely. The workpiece must be
shaped so that it can be clamped securely.
4. Technical data
Cordless Bandsaw
Motor power supply: ............................ 18V
Blade speed (surface feet per minute):
..........................................................393.7 SFPM
Blade length: .............................................44-7/8"
Blade width: .....................................................
Blade thickness: ......................................... 0.025"
Blade type (teeth per inch): ................... 10/14 TPI
Max. cutting width: ............................................ 5"
Max. cutting height: ....................................... 4-
Weight (tool only): ....................................12.1 lbs
Wear ear-muff s.
The impact of noise can cause damage to
hearing.
Reduce noise generation and vibration to a
minimum!
•
Use only equipment that is in perfect
condition.
•
Maintain and clean the equipment regularly.
•
Adapt your way of working to the equipment.
•
Do not overload the equipment.
•
Have the equipment checked if necessary.
•
Switch off the equipment when not in use.
•
Wear gloves.
CAUTION!
Residual risks
Even if you use this electric power tool in
accordance with the instructions, certain
residual risks cannot be eliminated. The
following hazards may arise in connection
with the equipment's construction and
layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
- 14 -
⁄
"
1
2
⁄
"
1
2
28.02.2024 10:43:51
28.02.2024 10:43:51
Publicité
