HIKOKI UP 18DA Mode D'emploi page 11

NOTE
*1 If the red lamp continues to blink even after the charger
has been attached, check to confirm that the battery
has been fully inserted.
*2 Battery overheated. Unable to charge.
Although charging will start once the battery has cooled
down even when left in situ, the best practice is to
remove the battery and allow it to cool down in a
shaded, well-ventilated location before charging.
*3 Malfunction in the battery or the charger
– Fully insert the battery.
– Check to confirm that no foreign matter is stuck to
the battery mount or terminals. If there are no
foreign objects, it is probable that the battery or
charger is malfunctioning. Take it to your authorized
Service Center.
○ When the battery charger has been continuously used,
the battery charger will be heated, thus constituting the
cause of the failures. Once the charging has been
completed, give 5 minutes rest until the next charging.
(2) Regarding the temperatures and charging time of the
battery (See Table 2)
Table 2
Model
Type of battery
Charging voltage
Temperatures at which the
battery can be recharged
1.5 Ah
2.0 Ah
2.5 Ah
Charging time for
3.0 Ah
battery capacity,
approx. (At 20°C)
4.0 Ah
5.0 Ah
6.0 Ah
1.5 Ah
(× 2 unit)
Charging time for
multi volt battery 2.5 Ah
capacity, approx. (× 2 unit)
(At 20°C)
4.0 Ah
(× 2 unit)
Number of battery cells
Charging voltage for USB
Charging current for USB
Weight
NOTE
○ The recharging time may vary according to the ambient
temperature and power source voltage.
○ If charging takes a long time
– Charging will take longer at extremely low ambient
temperatures. Charge the battery in a warm location
(such as indoors).
4. Disconnect the charger's power cord from the
5. Hold the charger firmly and pull out the battery.
NOTE
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period is
not activated, the electric discharge might be low when
using them the first and second time. This is a temporary
phenomenon, and normal time required for recharging will
be restored by recharging the batteries 2–3 times.
(1) Recharge the batteries before they become completely
UC18YSL3
Li-ion
(2) Avoid recharging at high temperatures. A rechargeable
14.4–18 V
0°C–50°C
15 min
20 min
25 min
20 min
(BSL1430C,
BSL1830C: 30 min)
26 min
(BSL1840M: 40 min)
32 min
38 min
20 min
32 min
52 min
4–10
5 V
*1 Power supply with 12 V DC adapter
WARNING
2 A
○ Do not use this product with power supply from a 12 V
0.6 kg
○ Before commissioning, check that the rated mains
○ Ensure that the 12 V DC adapter is not pinched or
11
– Do not block the air vent. Otherwise the interior will
overheat, reducing the charger's performance.
– If the cooling fan is not operating, contact a HiKOKI
Authorized Service Center for repairs.
receptacle.
Be sure to pull out the battery from the charger after
use, and then keep it.
Regarding electric discharge in case of new
batteries, etc.
How to make the batteries perform longer.
exhausted. When you feel that the power of the tool
becomes weaker, stop using the tool and recharge its
battery. If you continue to use the tool and exhaust the
electric current, the battery may be damaged and its life
will become shorter.
battery will be hot immediately after use. If such a
battery is recharged immediately after use, its internal
chemical substance will deteriorate, and the battery life
will be shortened. Leave the battery and recharge it
after it has cooled for a while.
MOUNTING AND OPERATION
Action
Inserting and removing the battery
(sold separately)
Charging
Power supply with 12 V DC adapter*
How to use the LED light
Remaining battery indicator
Charging a USB device from an
electrical outlet
Charging a USB device and battery
from an electrical outlet
How to recharge USB device
Selecting accessories
cigarette lighter while the vehicle is driving.
voltage, as stated on the type plate match your power
supply.
damaged.
English
Figure Page
3 2
4 3
1 5 3
10 4
11 4
12-a 4
12-b 4
13 4
― 227