Télécharger Imprimer la page

Makita DUB184RT Manuel D'instructions page 7

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 11
Important safety instructions for
battery cartridge
Before using battery cartridge, read all instruc-
1.
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using battery.
Do not disassemble battery cartridge.
2.
If operating time has become excessively
3.
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
If electrolyte gets into your eyes, rinse them out
4.
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
Do not short the battery cartridge:
5.
Do not touch the terminals with any con-
(1)
ductive material.
Avoid storing battery cartridge in a con-
(2)
tainer with other metal objects such as
nails, coins, etc.
Do not expose battery cartridge to water
(3)
or rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
Do not store the tool and battery cartridge in
6.
locations where the temperature may reach or
exceed 50 °C (122 °F).
7.
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
8.
9.
Do not use a damaged battery.
10. The contained lithium-ion batteries are subject to
the Dangerous Goods Legislation requirements.
For commercial transports e.g. by third parties,
forwarding agents, special requirement on pack-
aging and labeling must be observed.
For preparation of the item being shipped, consult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tape or mask off open contacts and pack up the
battery in such a manner that it cannot move
around in the packaging.
When disposing the battery cartridge, remove
11.
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
12. Use the batteries only with the products
specified by Makita. Installing the batteries to
non-compliant products may result in a fire, exces-
sive heat, explosion, or leak of electrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
SAVE THESE INSTRUCTIONS.
Only use genuine Makita batteries.
CAUTION:
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
Charge the battery cartridge before completely dis-
1.
charged. Always stop tool operation and charge the
battery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
2.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
3.
ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot
battery cartridge cool down before charging it.
Charge the battery cartridge if you do not use
4.
it for a long period (more than six months).
ASSEMBLY
Always be sure that the machine is
CAUTION:
switched off and the battery cartridge is removed
before carrying out any work on the machine.
Installing the front nozzle
1.
Loosen 2 screws with the hex wrench, and then
pull the screws all the way.
► Fig.1: 1. Screw
2.
Make sure that the Makita logo on the front nozzle
is facing the direction shown in the figure, and then
attach the front nozzle to the machine.
► Fig.2: 1. Front nozzle
3.
Tighten the screws with the hex wrench.
► Fig.3: 1. Screw
Installing the flat nozzle or extension nozzle
Optional accessory
1.
Attach the adapter pipe to the front nozzle, and
then turn it clockwise to lock it into place.
► Fig.4: 1. Adapter pipe 2. Front nozzle
2.
Attach the flat nozzle or extension nozzle to the
adapter pipe, and then turn it to lock it into place.
► Fig.5: 1. Flat nozzle 2. Extension nozzle 3. Adapter pipe
Attaching the shoulder strap
Optional accessory
Be sure to attach the hooks of the
CAUTION:
shoulder strap to the machine securely. If the hooks are
attached incompletely, they may come off and cause an injury.
Be sure to use the shoulder strap
CAUTION:
dedicated to this machine. Using other shoulder
strap may cause an injury.
Attach the hooks of the shoulder strap to the machine
as shown in the figure.
► Fig.6: 1. Hook
You can also attach the shoulder strap to the machine
as shown in the figure by attaching one end of the
shoulder strap to the buckle of the shoulder strap.
► Fig.7: 1. Buckle
7 ENGLISH

Publicité

loading

Ce manuel est également adapté pour:

Dub184