Skil 9005 Notice Originale page 10

• Grinding 8
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
• Cutting 9
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner
- do not apply pressure on the tool; let the speed of the
cutting disc do the work
- the working speed of the cutting disc depends on the
material to be cut
- do not brake cutting discs with side pressure
• Holding and guiding the tool
- always hold the tool firmly with both hands, so you will
have full control of the tool at all times
! while working, always hold the tool at the
grey-coloured grip area(s) 0
- provide for a secure stance
- pay attention to the direction of rotation; always hold
the tool so, that sparks and grinding/cutting dust fly
away from the body
- keep ventilation slots K 4 uncovered
APPLICATION ADVICE
• Instead of flange B 4 the "CLIC" quick-clamping flange
(SKIL accessory 2610388766) can be used; grinding/
cutting discs can then be mounted without the use of
accessory keys
• For more tips see www.skileurope.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots K 4)
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skileurope.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol ! will remind you of this when the need for
disposing occurs
DECLARATION OF CONFORMITY
• We declare under our sole responsibility that this product
is in conformity with the following standards or
standardized documents: EN 60745, EN 61000, EN
55014, in accordance with the provisions of the directives
2006/95/EC, 2004/108/EC, 2006/42/EC
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
06.06.2011
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 92 dB(A) and the sound
power level 103 dB(A) (standard deviation: 3 dB), and the
vibration ✱ (hand-arm method; uncertainty K = 1.5 m/s²)
✱ when surface grinding 10.5 m/s²
✱ when sanding 6.4 m/s²
! other applications (such as cutting-off or wire
brushing) may have different vibration values
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintainted accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Meuleuse d'angle
INTRODUCTION
• Cet outil sert au meulage, au tronçonnage et à l'ébarbage
léger de pièces en métal et en pierre sans utiliser de
l'eau; combiné avec des accessoires spécifiques, cet
outil peut également servir au brossage et au ponçage
• Cet outil n'est conçu pour un usage professionnel
• Ne jamais appliquez une trop forte pression sur
l'outil; laissez au disque le soin de faire le travail de
par sa propre vitesse
• Les opérations de coupe avec disques à tronçonner
abrasifs ne sont autorisées que si une protection de
tronçonnage (disponible en option comme
10
9005/9030/9035