Télécharger Imprimer la page

Gaggenau AC230101 Manuel D'utilisation Et Notice D'installation page 27

Publicité

Les langues disponibles
  • FR

Les langues disponibles

7.4 Switching on intensive mode
If particularly strong odours or vapours develop, you
can use intensive mode.
⁠   so oft drücken, bis in der LED-Anzeige die LED 4
1.
für die Intensivstufe 1 leuchtet.
⁠   so oft drücken, bis in der LED-Anzeige die LED 5
2.
für die Intensivstufe 2 leuchtet.
a After approx. 6 minutes, the appliance automatically
switches to fan setting 3.
7.5 Switching off intensive mode
To select a fan setting of your choice, press
7.6 Switching on automatic mode
The optimum fan setting is set automatically using a
sensor.
Press ⁠ .
a In the LED display, LED 6 lights up for automatic
mode.
7.7 Switch off automatic mode
Press ⁠ .
a The appliance switches to the fan setting that was
previously set.
a The ventilation is automatically ended when the
sensor detects no further change in the room air
quality.
a Automatic mode runs for a maximum of four hours.
7.8 Sensor sensitivity
In automatic mode, a sensor in the appliance detects
the intensity of the cooking odours and roasting
odours. Depending on the setting of the sensor sensit-
ivity, the optimum fan setting is automatically switched
on.
If the sensor control reacts too weakly or too strongly,
you can change the setting for the sensor sensitivity.
¡ Default setting: Fan setting 3
¡ Lowest setting: Fan setting 1
¡ Highest setting: Fan setting 5
7.9 Setting the sensor sensitivity
Requirement: The appliance is switched off.
Press and hold
⁠   and ⁠   for approx. 3 seconds.
1.
Press
⁠   or 
to change the setting.
2.
To cancel the setting, press  ⁠ .
To save the setting, press and hold
3.
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
a A signal tone sounds as soon as the selected set-
ting is saved.
7.10 Switching on intermittent ventilation
With interval ventilation, the ventilation switches on for
approx. 6 minutes every hour.
1
Depending on the appliance specifications
⁠ .
1
1
1
1
⁠   and  for ap-
Note: In the Home Connect app, you can set the time
and fan setting individually.
Press
⁠ .
a In the LED display, LED 6 flashes continuously, the
LED for the selected fan setting lights up on the ap-
pliance.
a As soon as the ventilation time ends, the LED for
the fan setting you have selected goes out. LED 6
continues to flash.
7.11 Switching off interval ventilation
Press
⁠ .
7.12 Saturation indicator
If the grease filters or odour filters are saturated, cor-
responding symbols flash after the appliance is
switched off.
Note: You can set the saturation indicator in the Home
Connect app depending on the filter used.
Clean the saturated grease filters and, in doing so, ob-
serve the cleaning instructions in these instructions.
Change the saturated odour filters and observe the in-
structions in the accompanying instructions.
If odour filters can be regenerated, follow the instruc-
tions in the accompanying instructions.
7.13 Resetting the saturation indicator
After cleaning the grease filter or after changing the
odour filter, the saturation indicator can be reset.
Requirements
¡ After the appliance has been switched off, LED 1
flashes in the LED display for the grease filter satura-
tion display and/or LED 2 flashes for the saturation
indicator for the odour filter.
¡ A signal sounds repeatedly.
Press
.
a The saturation indicator is reset.
7.14 Setting the saturation indicator
The saturation indicator must be adjusted depending
on the filter used.
Requirement: The appliance is switched off.
Press and hold
⁠   and
1.
To set circulating-air mode (non-regenerable fil-
ter), press
⁠ /
until LED 2 lights up in the LED
display.
To set circulating-air mode (non-regenerable fil-
ter), press
⁠ /
until LED 3 lights up in the LED
display.
To convert the electronic control back to opera-
tion without the air recirculation filter, press
until LED 1 lights up on the LED display.
2.
To save the setting, press and hold  ⁠   and  ⁠   for ap-
prox. three seconds.
Or wait approx. 10 seconds until the setting is
saved automatically.
Basic operation en
⁠   for approx. three seconds.
⁠ /
27

Publicité

loading