Publicité
Les langues disponibles
Les langues disponibles
The wheel may bind, walk up or kickback if the power
tool is restarted in the workpiece .
• Support panels or any oversized workpiece to minimize
the risk of wheel pinching and kickback . Large workpiec-
es tend to sag under their own weight . Supports must be
placed under the workpiece near the line of cut and near
the edge of the workpiece on both sides of the wheel .
• Use extra caution when making a "pocket cut" into exist-
ing walls or other blind areas . The protruding wheel may
cut gas or water pipes, electrical wiring or objects that
can cause kickback .
Safety warnings specific for sanding operations
• Do not use excessively oversized sanding disc paper . Fol-
low manufacturers recommendations, when selecting
sanding paper . Larger sanding paper extending beyond
the sanding pad presents a laceration hazard and may
cause snagging, tearing of the disc, or kickback .
Safety warnings specific for wire brushing
operations
• Be aware that wire bristles are thrown by the brush even
during ordinary operation . Do not overstress the wires
by applying excessive load to the brush . The wire bristles
can easily penetrate light clothing and/or skin .
• If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or brush
with the guard . Wire wheel or brush may expand in diam-
eter due to work load and centrifugal forces .
Additional safety warnings
• Wear safety goggles .
• Use suitable detectors to determine if utility lines are hid-
den in the work area or call the local utility company for
assistance . Contact with electric lines can lead to fire and
electric shock . Damaging a gas line can lead to explosion .
Penetrating a water line causes property damage or may
cause an electric shock .
• Release the On/Off switch and set it to the off position
when the power supply is interrupted, e . g ., in case of a
power failure or when the mains plug is pulled . This pre-
vents uncontrolled restarting .
• Do not touch grinding and cutting discs before they have
cooled down . The discs can become very hot while work-
ing .
• Secure the workpiece . A workpiece clamped with clamp-
ing devices or in a vice is held more secure than by hand .
MAINTENANCE AND CLEANING
Make sure that the machine is not live when carrying
out maintenance work on the motor .
• Regularly clean the machine housing with a soft cloth,
preferably after each use . Keep the ventilation slots free
from dust and dirt .If the dirt does not come off use a soft
cloth moistened with soapy water . Never use solvents
such as petrol, alcohol, ammonia water, etc . These sol-
vents may damage the plastic parts .
• The machine requires no additional lubrication .
• Should a fault occur, e .g . after wear of a part, please con-
tact your local SBM group GmbH dealer .
DISPOSAL
Discarded electric appliances are recyclable and
should not be discarded in the domestic waste!
Please actively support us in conserving resources
and protecting the environment by returning this
appliance to the collection centres (if available) .
In order to prevent the machine from damage during
transport, it is delivered in a sturdy packaging . Most of the
packaging materials can be recycled . Take these materials
to the appropriate recycling locations . Take your unwanted
machines to your local SBM group GmbH dealer . Here they
will be disposed of in an environmentally safe way .
Noise/Vibration Information
Measured in accordance with EN 60745-2-11 the sound
pressure level of this tool is 87,5 dB(A) and the sound power
level is 98,5 dB(A) (standard deviation: 3 dB), and the vibra-
tion is 5,43 m/s
2
(hand-arm method) .
Declaration of Conformity
We declare under our sole responsibility that this product
is in conformity with the following standards or standard-
ized documents: EN 60745-1, EN 60745-2-3, EN 55014-1, EN
55014-2, EN 61000-3-2, EN 61000-3-3, in accordance with
the regulations 2006/42/EC, 2006/95/EC, 2004/108/EC,
2011/65/EU .
13
Publicité
