Tecfrigo ENOPRESTIGE 600 5TV Installation Et Mode D'emploi page 6

Operator's guide:
1. Unpacking instructions
2. The handles
3. Laddered surface
I
4. Internal cleaning
5. External cleaning
UK
6. Connection to the mains
7. Control
D
8. Checking the correct functioning
9. Replacing the magnetic strip on the door
E
!
WARNINGS (See picture 10)
F
It is most important that this instruction booklet is kept together with the appliance both for future
reference and for reasons of safety.
NL
1 . Adults should operate this appliance only. Do not allow children to use the controls or play with it. . It
is forbidden to modify in any way the main functions and characteristics of this appliance. . The electrical
installation of the appliance should be carried out by a qualified electrician or other competent person.
P
4. Never attempt to carry out repairs unassisted. Inexpert repairs can cause serious damage and
malfunction. . Assistance has to be provided by an authorized engineer only. Always use original spare
S
parts. . This appliance is not suitable for the storage of basic commodities not including food-stuffs. 6
7. The manufacturers of this appliance accept no responsibility for the consequences of misuse in
DK
contravention of these safety instructions. It further reserves the right to carry out improvements without
prior notice.8
FIN
sources of heat (such as radiators, stoves, etc) and drafts (such as windows, doors, ventilation systems,
air conditioning, etc ...). 10
B
that the products displayed on the shelves and grills do not hang over the edges.
products to be refrigerated should cause ice to form on the evaporator, we recommend stopping the
compressor and placing the goods in special refrigerated containers, kept at the same temperature, until
GR
defrosting is completed;if this is not carried out the compressor will continue to operate leading to a
wasteful consumption of electricity and poor performance.
CZ
it is indispensable to keep the door open at least 10 cm.
EE
LV
1. UNPACKING INSTRUCTIONS
LT
CARDBOARD PACKAGING 1a. Cut the strap and lift up the cardboard packing.
WOODEN CRATE 1b.
H
between appliance and pallet or crate.
appliance on a horizontal level surface, using the feet to adjust.
the back of the appliance.
M
8. Separate the different packaging materials to facilitate disposal. (See picture 1)
PL
2. THE HANDLES
1. The handles are in a package inside the appliance. . Fasten the handle base with the two screws
SK
already inserted in the holes onto the jamb of the door. Tighten them.
it until it clicks. (See picture 2)
SLO
3. LADDERED SURFACE
1. The stainless steel bars and the bottle support surface are inside the appliance
guides are fixed to the sides inside the appliance.
be fitted in different positions.
plane. . Place the laddered surface on the "L" brackets which are on the sides inside the appliance. (See 5
picture 3)
4. INTERNAL CLEANING
1. Clean the internal elements and the glass only with a soft sponge and neutral detergents.
transparent protection tubes of the fluorescent lamps. Do not use detergents containing alcohol or other
solvents which could damage the tubes. Use only a soft damp cloth. . Dry with a soft cloth.
5. EXTERNAL CLEANING
1 . To clean use the same products used for the inside. . To clean the wooden surfaces, use specific
cleaning products generally available on the market, which should anyway be water-based emulsions,
free of all solvents. . Dry with a soft cloth.
5
. Avoid installing the cabinet directly in line with sunlight. . Never install the appliance near
. Keep the ventilation grills free from obstruction for at least 30 cm.
Remove the nails from the wooden crate with care.
7.
Make sure there is nothing left inside the packaging before disposal.
4. Insert a bar into the vertical side in order to support bottles on a sloped
3
Operator's guide
Maintenance manual (Page 48):
1. Cleaning the condenser
2. Replacement of the internal lamps
3. Wiring diagram diagram of refrigeration unit
13 . If the appliance is not working and unused,
3. 4.
Lift the appliance. Remove the pallet or crate. . Place the
6.
2
3.
Each vertical guide has notches to allow the bars to
2
6
3
9
12
. If damp air or
2. Insert forks of fork-lift truck
5
Insert the two spacers in the holes on
3.
Apply the plastic piece, pressing
. 2. The bar support
3
2
11 .Ensure
2. Clean the