Switching the power
tool on / off
Switching on:
Slide the on / off switch 6 forward without press-
ing� Press the front part of on / off switch 6 to fix it in
pressed position�
Switching off:
Push the back part of on / off switch 6�
Design features
of the power tool
Restart protection
Restart protection - prevents the power tool from
automatically starting up after a power cut� After a
power cut, the power tool must be actively turned off
before it can be started again�
Soft start
Soft start (limiting system of starting current) enables
smooth start of power tools - the disc is being run up
gradually with no jerks and kickbacks; no jump-like
load is imposed on the motor upon switching�
Recommendations
on the power tool operation
Cutting (see fig. 6.1)
• Install cutting disc as described below�
• Start the power tool, wait until the engine gains its
maximum speed and only after that, smoothly bring
cutting disc to the surface processed�
• Do not apply excessive pressure to the power tool,
as it will not bring better results but it will overload the
engine and wear out cutting disc faster�
• Move the power tool along the cutting line with mod-
erate feed, not distorting and not making vibrating and
bursting movements�
• Cutting should be implemented in the direction
shown on fig. 6.1. When cutting in the reverse direc-
tion the danger of uncontrolled throwing of the power
tool out to the side of the operator, which can lead to
serious injuries appears�
Grinding (see fig. 6.2)
Grinding is applied for the rough and quick grinding of
metals, the processing of welding seams, etc� Select
the type of grinding disc depending on the work, which
you are going to implement�
• Install grinding disc as described above�
• Start the power tool, wait until the engine gains its
maximum speed and only after that smoothly bring
grinding disc to the surface processed�
• Holding the power tool at an angle of 10° to 15° re-
lating to the surface processed (see fig. 6.2) is rec-
ommended� If this angle is less than recommended,
it will make controlling the power tool more difficult. If
this angle is more than recommended, the processing
The manufacturer reserves the possibility to introduce changes.
quality will decrease and grooves will be left on the
billet surface�
• Make alternate-reciprocal movements applying
moderate pressure to the power tool� Excessive pres-
sure will not bring better results but it will overload the
engine and create the danger of destruction of grinding
disc, which can cause severe injuries�
Power tool maintenance /
preventive measures
Before carrying out any works on the power tool it
must be disconnected from the mains�
Cleaning filter (see fig. 7)
Regularly inspect filter 8 (its contamination depends
on the state of the environment). Clean the filter 8 as
it gets dirty�
• Remove filter 8 as shown onto fig. 7.1.
• Clean filter 8 with soft brush or blow it with com-
pressed air�
• Install filter 8 as shown onto fig. 7.2.
Cleaning of the power tool
An indispensable condition for a safe long-term exploi-
tation of the power tool is to keep it clean� During the
long treatment of metal, current-conducting dust can
be accumulated inside the power tool. Regularly flush
the power tool with compressed air thought the ventila-
tion slots 3�
After-sales service and application service
Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts� Information about service centers,
parts diagrams and information about spare parts can
also be found under: www.dwt-pt.com�
•
Categorically not to drop any mechanical impact on
the packaging during transport�
• When unloading / loading is not allowed to use any
kind of technology that works on the principle of clamp-
ing packaging�
Recycle raw materials instead of dispos-
ing as waste.
Power tool, accessories and packaging
should be sorted for environment-friendly
recycling�
The plastic components are labelled for categorized
recycling�
These instructions are printed on recycled paper man-
ufactured without chlorine�
English
22
Transportation
of the power tools
Environmental
protection