Publicité
Liens rapides
Page 1 of 8
EH0099
FITTING INSTRUCTIONS FOR EH0099 EXHAUST HANGER
TO FIT KAWASAKI Z-H2 2020-
This kit contains the items pictured and labelled over page.
Some parts may be shown for clarity of instructions only.
Do not proceed until you are sure all parts are present.
Please read all instructions before proceeding.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
Please note that the way the kit is packed does not necessarily represent the way of
mounting to the bike.
In the event of rubber washers being used to hold components onto bolts,
these rubber washers can be thrown away.
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM
WWW.RG-RACING.COM
R&G
Unit
, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
1
Tel: +44 (0)
420 89007 Fax: +44 (0)
420 87301
www.rg-racing.com
Email:
info@rg-racing.com
1
1
Publicité
Manuels Connexes pour R&G EH0099
Sommaire des Matières pour R&G EH0099
- Page 1 Page 1 of 8 EH0099 FITTING INSTRUCTIONS FOR EH0099 EXHAUST HANGER TO FIT KAWASAKI Z-H2 2020- This kit contains the items pictured and labelled over page. Some parts may be shown for clarity of instructions only. Do not proceed until you are sure all parts are present.
- Page 2 Page 2 of 8 EH0099 TOOLS REQUIRED GENERAL TORQUE SETTINGS Set of metric Allen keys to include M4 BOLT = 8Nm 5mm. M5 BOLT = Spanner set to include 12mm & M6 BOLT = 13mm, spanners. M8 BOLT = 20Nm...
- Page 3 Page 3 of 8 EH0099 ASSEMBLY DIAGRAM FITTING INSTRUCTIONS • Remove the original RHS pillion footrest from the bike. To do this, first remove the OEM nut from the back of the original exhaust using a spanner and Allen key to hold the bolt.
- Page 4 Page 4 of 8 EH0099 • Offer the exhaust hanger into position on the bike affix the two bolts into the corresponding threaded holes on the frame left by the foot peg hanger. • Ensure the exhaust hanger lines up correctly with the exhaust and tighten the bolts to the recommended torque.
- Page 5 Page 5 of 8 EH0099 NOTICE DE MONTAGE POUR EH0099 SUPPORT D’ÉCHAPPEMENT POUR KAWASAKI Z-H2 2020- E KIT CONTIENT LES ARTICLES ILLUSTRES ET ETIQUETES SUR LA PAGE ERTAINES PARTIES PEUVENT ETRE PRESENTES UNIQUEMENT POUR LA CLARTE DES INSTRUCTIONS E PAS PROCEDER AU MONTAGE TANT QUE VOUS N...
- Page 6 Page 6 of 8 EH0099 OUTILS REQUIS VALEURS DE SERRAGE RECOMMANDÉES Clé Allen 5mm. M4 BOULON = 8Nm Clé à molette 12mm & 13mm. M5 BOULON = 12Nm M6 BOULON = 15Nm M8 BOULON = 20Nm 0 BOULON = 40Nm M12 BOULON = 40Nm LÉGENDE...
- Page 7 Page 7 of 8 EH0099 SCHÉMA D’ENSEMBLE NOTICE DE MONTAGE • Retirez le repose-pied passager côté droit d'origine de la moto. Pour ce faire, retirez d'abord l'écrou d’origine de l'arrière de l'échappement d'origine à l'aide d'une clé à molette et d'une clé...
- Page 8 Page 8 of 8 EH0099 • Vissez ces boulons dans les trous supérieurs du support d'échappement R&G (HB0099 - ARTICLE 1) comme indiqué sur le schéma de montage. • Présentez le support d'échappement en place sur la moto et fixez les deux boulons dans les trous filetés correspondants sur le cadre à...