Publicité
PAGE 1 OF 9
FITTING INSTRUCTIONS FOR EH0094 EXHAUST HANGER BRACKET
T
HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE
S
OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY
D
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
P
LEASE NOTE THAT THE WAY THE KIT IS PACKED DOES NOT NECESSARILY REPRESENT THE WAY OF
I
N THE EVENT OF RUBBER WASHERS BEING USED TO HOLD COMPONENTS ONTO BOLTS
DIGITAL COPIES OF THESE INSTRUCTIONS ARE AVAILABLE FROM:
Unit 1, Shelleys Lane, East Worldham, Alton, Hampshire GU34 3AQ.
Tel: +44 (0)1420 89007 Fax +44 (0)1420 87301
INDIAN FTR 1200 2019-
O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT
P
LEASE READ ALL INSTRUCTIONS BEFORE PROCEEDING
MOUNTING TO THE BIKE
THESE RUBBER WASHERS CAN BE THROWN AWAY
WWW.RG-RACING.COM
Picture A
.
R&G Racing
www.rg-racing.com
.
.
.
.
.
Email:
info@rg-racing.com
EH0094
,
Publicité
Table des Matières
Manuels Connexes pour R&G EH0094
Sommaire des Matières pour R&G EH0094
- Page 1 EH0094 PAGE 1 OF 9 FITTING INSTRUCTIONS FOR EH0094 EXHAUST HANGER BRACKET INDIAN FTR 1200 2019- Picture A HIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED OVER PAGE OME PARTS MAY BE SHOWN FOR CLARITY OF INSTRUCTIONS ONLY O NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT...
- Page 2 PAGE 2 OF 9 EH0094 TOOLS REQUIRED GENERAL TORQUE SETTINGS • Set of metric Allen keys to include 6 and M4 BOLT = 8Nm M5 BOLT = • Socket or spanner set to include 12mm M6 BOLT = • T40 Torx tool...
-
Page 3: Assembly Diagram
EH0094 PAGE 3 OF 9 ASSEMBLY DIAGRAM 1 R&G Racing Unit 1, Shelleys Lane, East Worldham, Alton, Hampshire GU34 3AQ. Tel: +44 (0)1420 89007 Fax +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com... - Page 4 PAGE 4 OF 9 EH0094 Picture 2 Picture 1 Picture 3 Picture 4 R&G Racing Unit 1, Shelleys Lane, East Worldham, Alton, Hampshire GU34 3AQ. Tel: +44 (0)1420 89007 Fax +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
-
Page 5: Fitting Instructions
EH0094 PAGE 5 OF 9 FITTING INSTRUCTIONS • To fit the R&G Exhaust Hanger, the OEM pillion footrest mounting bracket needs to be removed. • To do this, remove the two mounting bolts on the riders heal guard as shown in picture 1 holding the reservoir in place so that the reservoir can be temporarily relocated to allow access to the bolt. - Page 6 PAGE 6 OF 9 EH0094 NOTICE DE MONTAGE EH0094 SUPPORT D’ECHAPPEMENT Photo A E KIT CONTIENT LES ARTICLES EN PHOTO ET ETIQUETTES SUR LA PAGE LES PARTIES PRESENTÉES PEUVENT ETRE UNIQUEMENT REPRESENTATIVES POUR LA CLARTE DES INSTRUCTIONS E PAS ROCÉDER AU MONTAGE AVANT DE VOUS ÊTRES ASSURE QUE TOUTES LES PIÈCES SOIENT PRÉSENTES SVP, ’...
-
Page 7: Outils Requis
EH0094 PAGE 7 OF 9 OUTILS REQUIS ALEURS DE SERRAGE • Clés Allen 6 et 8mm M4 BOULON = 8N • Clé à cliquet + douille 12mm M5 BOULON = 12N • Clé Torx T40 M6 BOULON = 15N M8 BOULON = 20N... -
Page 8: Schema De Montage
PAGE 8 OF 9 EH0094 SCHEMA DE MONTAGE R&G Racing Unit 1, Shelleys Lane, East Worldham, Alton, Hampshire GU34 3AQ. Tel: +44 (0)1420 89007 Fax +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com... - Page 9 EH0094 PAGE 9 OF 9 NOTICE DE MONTAGE • Pour monter le support d'échappement R&G, le support de fixation d’origine du repose-pieds passager doit être retiré. • Pour ce faire, retirez les deux boulons de montage sur la protection des pilotes comme indiqué sur la photo 1 en maintenant le réservoir en place afin que le réservoir puisse être temporairement...