NAD C 521BEE Manuel D'installation page 6

11. SKIP
During playback, press the SKIP
beginning of the current track. Press SKIP
to skip back to the previous track or previous programmed track in
Program Play mode, once to reach the beginning of the current track
and again to jump to the previous track. When pressing continuously,
the player will skip to previous tracks repeatedly, concluding at the
beginning of the disc (Track 1) or the first track programmed in Program
Play mode.
During playback, press the SKIP
the next track on the disc or next programmed track in Program Play
mode. Thus, to sample each song, press PLAY and then tap SKIP after
you've heard a few seconds of each track. From Stop, press the SKIP
button until you've reached the track from where you want to
start playback. Press Play to start playback.
12. STAND-BY INDICATOR
The stand-by indicator turns on in green when the unit is switched on,
and changes to amber when switched to stand-by mode.
REMOTE CONTROL
A wireless remote control is provided with your compact disc player,
enabling you to operate play-back functions from the comfort of your
chair or from virtually anywhere in the room. For reliable operation there
should be a clear line-of-sight path from the remote control to the front
of the CD player. If the player does not respond to remote commands,
it may be that this line-of-sight path is obstructed by clothing, paper, or
furnishings.
Most of the buttons on the remote control handset have the same
effect as the corresponding buttons on the front panel of the disc player.
In addition the handset is equipped with some extra buttons and
functions, such as the numeric keypad and Program functions.
POWER ON
Press the Green button to swith on the power to the disc player from
stand-by mode. The LED will change from amber to green, and the
display will illuminate.
POWER OFF
Press this red button to switch to stand-by mode from power on mode.
The LED will change from green to amber and the display will go dark.
NUMERIC KEYPAD
Using the direct-entry numeric keypad (1 to 10; +10) causes the player
to jump directly to the beginning of a numbered track and commence
play. Thus to play Track 5, simply press 5. To play Track 20, press: +10,
10. To play Track 36, press: +10, +10, +10, 6.
6
button once to skip back to the
twice in rapid succession
once to skip to the beginning of
PROGRAM
The C 521BEE CD player allows for programmed playback of up to 20
tracks in any desired order. To engage Program Play with your desired
track sequence in the memory:
1 Press PROGRAM. The "MEMORY" indicator will light up. The display
indicates "Pr p:01", meaning that the player is awaiting the first
Program entry.
2 Use the SKIP or the Direct-Entry Numeric keypad buttons to select
the first track in your planned sequence. The selected track number
will blink in the display.
3 Press PROGRAM to store the selected track number in memory. The
display will revert to show Program-Entry mode and advance to "Pr
p:02", showing that the player is ready for your second entry.
4 Repeat Steps 2 and 3 to select and store other track numbers in
memory, up to a maximum of 20 entries. The display will show
"FULL" when 20 tracks have been entered.
5 If you want to review or edit your program entries, press PROGRAM
repeatedly to cycle the display through them. When the highest
program number is displayed, you can enter additional tracks in the
memory by repeating Steps 2 and 3.
6 To play the stored program, press PLAY. "MEMORY" will appear in
the display, indicating that a stored program is being played. During
Program Play the SKIP buttons will access only the tracks in the
program list. So if you want to play only a portion of a stored
program, initiate play and press SKIP
programmed tracks that you don't want to hear.
7 To terminate program play, press STOP. However the stored track list
remains in memory; if you want to play the program again, simply
press PLAY again. If you want to edit the program, press PROGRAM
repeatedly to review the list and change. To add tracks, press the
PROGRAM button until the highest program number is displayed.
8 To clear the program memory, press STOP, OPEN/CLOSE to open the
drawer, or switch off the POWER.
The following example presents a step-by-step illustration of how to
program and start Program Play to play tracks 5, 23, 9, 16, and 1.
While the CD player is stopped:
Press on remote control
PROGRAM
5
PROGRAM
+10, +10, 3
PROGRAM
9
PROGRAM
+10, 6
PROGRAM
1
PROGRAM
PLAY
to jump over the
Display shows
Pr p:01
5 p:01
Pr p:02
23 p:02
Pr p:03
9 p:03
Pr p:04
16 p:04
Pr p:05
1 p:05
Pr p:06