ADEO SCREEN ELEGANCE PSCHP0200 Manuel D'instructions page 7

MEMORISING THE "FIRST" TRANSMITTER ON SCREEN
Caution! – DO NOT follow this procedure if Transmitters have already been memorised on screen.
01. Turn on the power to screen: the motor makes 2 LONG motions (= no transmitters memorised).
02. (Within the next 5 seconds) Press and hold down key
(= memorisation complete).
Caution! – Once this part of programming has been completed, the Up and Down movements of the motor are still not associated to keys
Transmitter. This will take place automatically during one of the three programming procedures of limit switches "0" and "1".
PROGRAMMING OF LIMIT SWITCH POSITIONS upper "0" and lower "1"
01. Press and hold down key (or
ATTENTION!!! the correct "0" position is when the low bar of the screen is positioned at 2 mm from the case.
02. Press and hold down key until the motor performs 1 VIBRATION; then release the key.
03. Press and hold down key again (for approx. 5 seconds), until the motor performs 4 SHORT motions; then release the key.
04. Press and hold down key until the motor performs 2 LONG motions (= the "0" position is memorised); then release the key.
05. Press and hold down key (or
06. Press and hold down key until the motor performs 1 VIBRATION; then release the key.
07. Press and hold down key again (for approx. 5 seconds), until the motor performs 4 SHORT motions; then release the key.
08. Press and hold down key until the motor performs 2 LONG motions (=position "1" is memorised); then release the key.
Note – Once this programming procedure is complete, key
Down manoeuvre. The roller shutter/awning will stop at programmed positions "0" and "1" during each of these manoeuvres.
REPOSITIONING OF LIMIT SWITCH lower "1"
01. Press and hold down key (for approx. 5 seconds), until the motor performs 1 VIBRATION, then release the key.
02. Press and hold down keys and
then release the keys.
03. (within the next 4 seconds) Press keys
04. (within the next 4 seconds) Press and hold down keys
release the keys
DELETING TRANSMITTERS FROM THE MEMORY
Caution! – This procedure deletes all memorised transmitter codes from screen memory. The procedure can be performed both with a memorised
transmitter as well as a non memorised transmitter.
If the transmitter is memorised, proceed as follows:
01. Press and hold down key (for approx. 5 seconds), until the motor performs 1 VIBRATION; then release the key.
02. Press and hold down key until the motor performs 3 LONG motions; then release the key exactly on the third movement.
03. Press and hold down key until the motor performs 3 LONG motions; then release the key exactly on the third movement.
04. Press and hold down key until the motor performs 3 LONG motions; then release the key exactly on the third movement.
After a few seconds the motor performs 5 LONG motions (= all transmitters deleted).
If the Transmitter is not memorised, proceed as follows:
A. Disconnect from power supply (if connected) and connect again the tubular motor to the power supply. Within the next 60 seconds,
press and hold down key (for approx. 5 seconds), until the motor performs 1 VIBRATION; then release the key.
B. (within the next 5 seconds) Disconnect from the power supply.
C. Power the motor again: the previous procedure, from point 01 to point 04, must be performed within 60 seconds from turning on the power supply.
ANOMALY
Screen does not open/close
Screen does not open/close
Screen moves in one direction only
Screen has come down but will not go up
R.I. screen is blocked
As is the case for installation procedures, when the product reaches the end of its useful life, disposal operations must be carried out by qualified
personnel.
The product is made up of various types of material: some can be recycled, others have to be disposed of. You must follow applicable recycling or
disposal regulations in force in your area for this product category.
As shown in the picture on the left, you must not throw the product into a domestic litter bin. Either dispose of the various components separately,
pursuant to the regulations applicable in your territory, or hand the product over to a vendor upon purchasing a similar new product.
Warning: local regulations can foresee heavy fines in case of unlawful disposal of this product.
Screens are covered by a 24 month guarantee for projection curtains, plus 12 months for mechanical and structural parts, and a 60 month period for
motors installed on single products.
The guarantee's validity starts from the date of purchase on the part of the end user; such purchase date must be documented by a purchase
receipt when requesting technical interventions or replacement.
The guarantee covers damages and malfunctions resulting from normal use of the products, and replacement free of charge of components with
manufacturing flaws; the service includes collection/delivery by a contracting courier at the manufacturer's expense (only for Italy and Poland
guarantees).
The guarantee is forfeited in case of incorrect use or installation, tampering or repair on the part of personnel not authorised by manufacturer or
tampering with the seal for end stop adjustment, which can only be carried out by technicians or specialised personnel. The guarantee does not
cover damages resulting from normal wear and tear or from particular weather or environmental conditions. Damages to goods during transport or
handling operations are not covered by guarantee.
Goods must therefore be checked carefully upon receival.
Screens returned for repair will not be accepted unless they are accompanied by the manufacturer's RMA (return material authorisation) and
adequately packed.
Manufacturer reserves the right to verify the existence of the requisites for the validity of the guarantee.
on the transmitter for about 3 seconds and release it as soon as the motor start the first of 3 LONG motions
) on the transmitter until the roller shutter/awning reaches the "0" position required by the user; then release the key.
) until the roller shutter/awning reaches the position "1" required by the user; then release the key.
on the Transmitter will control the Up manoeuvre of the roller shutter/awning, while key
simultaneously (for approx. 5 seconds), until the motor starts to automatically move the roller shutter / awning into position "1",
and to position the roller shutter/awning in the new position "1".
and simultaneously until the motor performs 2 LONG motions (= new position "1" memorised), then
TROUBLESHOOTING
POSSIBLE CAUSE
Not connected to power supply
The motor's thermal protection is activated
A power supply cable has not been connected
End stop has been incorrectly modified
Remote control batteries are flat
PRODUCT'S DISPOSAL
WARRANTY ON SCREENS
REMEDIAL ACTION
Check electrical connection
Allow to cool down for about 10 minutes
Check connection to selector switch
Call vendor or a technician for assistance
Replace batteries
and on the
will control the