Stopping, Pausing Or Restarting; Drying And Cycle Tips - Whirlpool Cabrio WGD6600VW1 Guide D'utilisation Et D'entretien

How the AccelerCare™ Drying System Works
Moisture-sensing strips and temperature sensors inside the
dryer drum monitor how fast the load is drying, how hot the
air should be and when clothes are dry. The system
automatically stops the cycle to help save time and avoid
overdrying.
To use a Timed Cycle
Turn knob to desired Timed Cycle.
Press the TIME ADJUST up or down arrows until the
desired drying time is displayed. Press the up or down
arrows and the time will change by 1-minute intervals.
Press and hold the up or down arrows and the time will
change by 5-minute intervals.
NOTE: The Time Adjust features can be used only with
the Timed Dry and the Enhanced Touch Up cycles.
Press TEMP until the desired temperature illuminates.
NOTE: The Temp feature can be used only with the Timed
Dry and the Enhanced Touch Up cycles.
NOTE: During theTimed Dry Cycle, you can change the
settings for Time, Temp, the WRINKLE SHIELD™ setting and
the End of Cycle Signal.
5. (OPTIONAL STEP) If desired, select OPTIONS. For more
details, see "Options."
6. (OPTIONAL STEP) If desired, press END OF CYCLE SIGNAL.
A signal will sound to alert you when a cycle ends. For more
details, see "End of Cycle Signal."
7. Press START. Be sure the door is closed.
If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.
If you wish to end your drying cycle after pressing Start,
press PAUSE/CANCEL twice.
To use a Steam Cycle
(Quick Refresh and Enhanced Touch Up)
Press POWER.
Turn the knob to select either the Enhanced Touch Up or
the Quick Refresh cycles.
Press the TIME ADJUST up or down arrows until the
desired drying time is displayed. Press the up or down
arrows and the time will change by 1-minute intervals.
Press and hold the up or down arrows and the time will
change by 5-minute intervals.
NOTE: The Time Adjust features can be used only with
the Timed Dry and the Enhanced Touch Up cycles.
Press TEMP until the desired temperature illuminates.
NOTE: The Temp feature can be used only with the Timed
Dry and the Enhanced Touch Up cycles. Only the Medium
and High temperature settings can be used for the
Enhanced Touch Up Cycle.
NOTE: During the Enhanced Touch Up cycle, you can change
the settings for Time Adjust and Temp. Open the door or
press PAUSE/CANCEL once to pause the cycle, or press
PAUSE/CANCEL twice to cancel a cycle.

Stopping, Pausing or Restarting

To stop or pause your dryer at any time
Open the door or press PAUSE/CANCEL once. Press PAUSE/
CANCEL twice to cancel a cycle.
To restart the dryer
Close the door. Press START until dryer starts.
NOTE: Drying will continue from where the cycle was interrupted
if you close the door and press Start within 5 minutes. If the cycle
is interrupted for more than 5 minutes, the dryer will shut off.
Select new cycle settings before restarting the dryer.

Drying and Cycle Tips

Select the correct cycle and dryness level or temperature for your
load. If an Automatic Cycle is running, the display shows the
estimated cycle time when your dryer is automatically sensing
the dryness level of your load. If a Timed Cycle is running, the
display shows the exact number of minutes remaining in the
cycle.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Drying tips
Follow care label directions when they are available.
If desired, add a fabric softener sheet. Follow package
instructions.
To reduce wrinkling, remove the load from the dryer as soon
as tumbling stops. This is especially important for permanent
press, knits and synthetic fabrics.
Avoid drying heavy work clothes together with lighter fabrics.
This could cause overdrying of lighter fabrics and lead to
increased shrinkage or wrinkling.
Cycle tips
Dry most loads using the preset cycle settings.
Refer to the Automatic or Timed Preset Cycle Settings chart
(in the "Cycles" section) for a guide to drying various loads.
Drying temperature and dryness level are preset when
you choose an Automatic Cycle. You can select a
different dryness level, depending on your load, by
pressing Dryness and choosing More, Normal, Less or
Damp.
NOTE: You cannot use the Time Adjust and you cannot
choose a Temperature with the Automatic Cycles.
15