Mounting Of Flue Pipe; Service; Optional Equipment - Jøtul F 400 Manuel D'installation Et Données Techniques

ENGLISH
2. Insert the ash lip, which is stored inside the burn chamber,
into the grooves under the door.
3. The burn chamber also contains a heat shield, which is to be
mounted under the ash house. Unfold the heat shield (see
fig. 2A) and fasten it with the two screws attached to the
ash house (2B).
4. Screw the door handle knobs to the front door handle and
the ash door handle. (Fig. 3B+C and fig. 7).

Mounting of flue pipe

Jøtul F 400 is factory-assembled for a top flue outlet. If a rear flue
outlet is preferred, loosen the two screws on the sides and rotate
the connecting pipe 180 0 . Then fasten the screws securely.
1. The 150 mm diameter flue pipe is placed directly with the
narrowest outer end onto the product flue outlet. There is a
screw on each side of the product flue outlet (fig. 4A). These
will be used to fasten the flue pipe.
2. Indicate with marks where the screws hit the flue pipe when
the pipe is at the bottom of the flue outlet and drill a 5,5 mm
hole in the flue pipe for the screw.
3. Use a gasket rope to seal the space between the flue pipe
and the product flue outlet.
4. Fasten the flue pipe with the screws.
Note! It is important that the joints are completely sealed. Air
leakage etc. may lead to malfunction.
3.6 Control of functions (fig. 3)
When the product is set up, always check the control functions.
These shall move easily and function satisfactorily.
Jøtul F 400 is equipped with the following controls:
Air vent (A)
Left position =
Right position =
Doorhandle (B)
Towards the left =
Towards the right =
Ash door (C)
Open the door by turning the door handle counter-clockwise one
half rotation. Use a glove or similar and pull out the tray.
3.7 Ash removal
Jøtul F 400 has an ash pan which makes it easy to remove the
ashes.
1. Push/pull the handle for the ash grate/ignition vent out and in
several times so that the ashes fall down into the ash pan. Use
something like a glove to grab the handle on the ash pan.
2. Make sure that the ash pan doesn't fill up so high that it keeps
ash from coming through the grate into the pan.
3. Make sure the door to the ash pan is securely shut when the
stove is in use.
For the rest, see description of how to handle ash in the Manual
on general use and maintenance in Point
measures».
18
closed.
fully open.
open.
closed.
«6.1 Fire preventive

4.0 Service

Warning! Any unauthorised change to the product is illegal. Only
use original spare parts.
4.1 Replacing the baffle plate
1. Lift off the top plate.
2. The baffle plate rests on top of the burn plates.
3. To remove the baffle plate, loosen the brackets that push it
down against the burn plates. Use a hammer and beat them
carefully out towards the door. See fig. 5
4. Lift the baffle plate a little upwards and remove it edgeways
out through the top.
For re-installation follow the same procedure in the opposite
sequence.
4.2 Replacing the burn plates
1. The fireplace has side burn plates, which are fastened with
screws. The rear burn plate is not fastened and is kept in place
by the side burn plates.
2. When replacing remove the baffle plate first, then loosen the
screws and remove the burn plates.

5.0 Optional equipment

5.1 Short legs - height 155 mm
Black paint - cat. no. 51012177 (350173)
Blue-black enamel - cat. no. 51012178 (350174)
Ocean green enamel - cat. no. 51012190 (350328)
Ivory enamel - cat. no. 51012179 (350176)
5.2 Rear heat shield
Black paint cat no. 50012949 (350694)
Enamel cat. no. 50012950 (350695)
5.3 Connecting pipe for outdoor
ventilation - cat. no. 50012842
With the aid of a connecting pipe for outdoor ventilation and a
flexible tube, combustion air can be connected to the product
directly from the outside. In this manner, the fireplace will always
be supplied with the air needed to achieve proper combustion.
Fresh air supply direct from the exterior or from the
chimney with air vents
1. Insert the connecting pipe into the air inlet under the
product.
2. Unfold the pipe"s 3 flaps (fig. 8A) inside the air inlet.
3. Attach a flexible tube (Ø 80 mm) directly to the fireplace's
connecting pipe by using a hose clamp and attach it to the
wall outlet/chimney