Publicité
Les langues disponibles
Les langues disponibles
RECIRCULATING
C
INSTALLATION OVERVIEW
C1. Attach Mounting Plate to Wall
C2. Prepare Top Cabinet
C3. Check Blower Plate
C4.
Mount the Microwave Oven
Install or change Charcoal Filter
C5.
IMPORTANT NOTES:
•
Make sure the screws for the blower motor and blower
plate are securely tightened when they are reinstalled.
This will help to prevent excessive vibration.
•
Make sure the motor wiring has been properly routed
and secured, and that the wires are not pinched.
C1.
ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
NOTE:
If the cabinet depth including the cabinet doors
is more than 13" " ' ' then the unit must be spaced
out from wall using adequate materials supporting
150 Ibs to allow proper top vent air exhaust.
Cabinet
Installation Instructions
(Non-Vented Ductless)
Cabinet
EN-20
3/8" TO EDGE
Trim the rear wall template
along the dotted line.
12"
TO
NOTE: IT IS VERY IMPORTANT
READ AND FOLLOW
THE DIRECTIONS
IN THE INSTALLATION
INSTRUCTIONS
BEFORE PROCEEDING
WITH THIS
REAR WALL TEMPLATE.
serves to position the bottom
4"
This Rear Wall Template
the horizontal exhaust
mounting plate and to locate
outlet.
the template is positioned
1. Use a level to check that
2. Locate and mark at least
accurately.
one stud on the left or
right side of the centerline.
It is important to use at
least one wood
screw mounted firmly in
a stud to support the weight
of the microwave. Mark
two additional, evenly spaced
locations for the supplied
toggle bolts.
3. Drill holes in the marked
for wood screws. For holes
locations. Where there is
a stud, drill a 3/16" hole
stud, drill 5/8" holes for
that do not line up with a
toggle bolts.
MOUNTING PLATE
DO NOT INSTALL THE
AT THIS TIME.
from the rear wall.
4. Remove the template
Instruction book for your
5. Review the Installation
installation situation.
para consultar la
Darle vuelta a la hoja
versión en Español.
Locate and mark holes
to align with holes in the
mounting plate.
LOCATE AT LEAST ONE
IMPORTANT:
STUD ON EITHER SIDE
OF
THE CENTERLINE.
MARK THE LOCATION
FOR 2 ADDITIONAL,
EVENLY
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
AREA.
Locate and mark holes
to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE
STUD ON EITHER SIDE
OF
THE CENTERLINE.
EVENLY
MARK THE LOCATION
FOR 2 ADDITIONAL,
along the dotted line.
SPACED TOGGLE BOLTS
IN THE MOUNTING PLATE
Trim the rear wall template
AREA.
IMPORTANT :Do not remove the cardboard
spacers between the heat shield and door.
1
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate through
2
the holes designated to go into drywall and
reattach the toggle wings to
each bolt.
To use toggle bolts:
Spacing for Toggles
More Than Wall
Thickness
Toggle Wings
Mounting
Toggle
Plate
Bolt
Wall
3
Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
4
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
3
" (19 mm) onto
⁄
4
Bolt End
Publicité
