Bosch GSB 600 Professional Notice Originale page 7

Technical data
Impact drill
Article number
Rated power input
Power output
No-load speed
Impact rate at no-load speed
Rated torque
Clockwise/anticlockwise ro-
tation
Spindle collar diameter
Max. drilling diameter
– Concrete
– Masonry
– Steel
– Wood
Chuck capacity
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Noise/vibration information
Noise emission values determined according to
EN 62841-2-1.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 99 dB(A); sound power level
107 dB(A). Uncertainty K = 5 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-1:
2
Drilling into metal: a = 5.2 m/s , K = 1.5 m/s
h
Impact drilling into concrete: a = 25.3 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Bosch Power Tools
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
GSB 600
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
3 601 AA0 3..
W 600
Assembly
W 300
–1 u
min 0–3000
–1
min 0–48000
Nm 1.4 Auxiliary handle (see figure A)
●
u
mm 43
You can adjust the auxiliary handle (6) to any of 12 positions
in order to achieve a safe work posture that minimises fa-
tigue.
mm 13
Turn the lower gripping end of the auxiliary handle (6) in ro-
mm 13
tational direction ➊ and push the auxiliary handle (6) for-
mm 10
ward until you can swivel it into the required position. Then
pull the auxiliary handle (6) back again and turn the lower
mm 25
gripping end in rotational direction ➋ to tighten it.
mm 1.5–13
Setting the drilling depth (see figure A)
kg 1.7
You can use the depth stop (7) to set the required drilling
depth X.
/II
Turn the lower gripping end of the auxiliary handle (6) anti-
clockwise and set the depth stop (7).
Pull the depth stop (7) far enough out that the distance
between the drill bit tip and the edge of the depth stop (7)
corresponds to the required drilling depth X.
Then turn the lower gripping end of the auxiliary handle (6)
clockwise to retighten it.
The fluting on the depth stop (7) must face downwards.
Changing the Tool
u
2
,
Keyed chuck (see figure B)
2 2
, K = 1.5 m/s .
Open the keyed chuck (1) by turning it until the tool can be
inserted. Insert the tool.
Insert the drill chuck key (9) into the corresponding holes of
the keyed chuck (1) and clamp the tool evenly.
Screwdriving tools (see figure C)
You should always use a universal bit holder (11) when using
screwdriver bits (10). Only use screwdriver bits that fit the
screw head.
For screwdriving, make sure the "drilling/impact drilling" se-
lector switch (2) is always set to the "drilling" symbol.
Dust/Chip Extraction
Dust from materials such as lead-containing coatings, some
wood types, minerals and metal can be harmful to one's
health. Touching or breathing-in the dust can cause allergic
reactions and/or lead to respiratory infections of the user or
bystanders.
Pull the plug out of the socket before carrying out any
work on the power tool.
Do not operate your power tool without the auxiliary
handle (6).
Wear protective gloves when changing tools. The drill
chuck may heat up significantly when it is used for long
periods.
1 609 92A 899 | (01.12.2022)
English | 7