Balluff BTL7-V50D-M Serie Notice D'utilisation page 36

BTL7-V50D-M _ _ _ _ -A/B/Y/Z(8)-C003
Transducer — Rod Style
6
Technical data
6.1 Accuracy
The specifications are typical values for the BTL7-V50D...
at 24 V DC and room temperature, with a nominal length
of 500 mm in conjunction with the BTL-P-1013-4R,
BTL-P-1013-4S, BTL-P-1012-4R or BTL-P-1014-2R
magnet.
The transducer is fully operational immediately, with full
accuracy after warm-up.
For special versions, other technical data may
apply.
Special versions are indicated by the suffix -SA
on the part label.
Position resolution
Non-linearity with a constant
distance between the magnet and
profile:
Nominal length ≤ 5500 mm
Nominal length > 5500 mm
Hysteresis
Repeat accuracy
Temperature coefficient
1)
Velocity resolution
Min. detectable velocity
Max. detectable velocity
6.2 Ambient conditions
Operating temperature
Storage temperature
Humidity
Rod pressure rating (when installed
in hydraulic cylinders)
For Ø 8 mm
For Ø 10.2 mm
Shock rating
Continuous shock
per EN 60068-2-27
3)
Vibration
per EN 60068-2-6
3)
Degree of protection per IEC 60529
Connector C003 (when attached)
14 english
1 µm
±30 µm
±0.02 % FS
≤ ±10 µm
≤ ±5 µm
(typ. ±2.5 µm)
≤ 18 ppm/K
0.1 mm/s
1 mm/s
10 m/s
2)
−40°C...+85°C
−40°C...+100°C
< 90%, non-
condensing
< 250 bar
< 600 bar
150 g/6 ms
150 g/2 ms
20 g, 10...2000 Hz
IP67
6.3 Supply voltage (external)
Voltage, stabilized
4)
Ripple
Current draw
(at 24 V DC)
Inrush current
Reverse polarity protection
Overvoltage protection
Dielectric strength
(GND to housing)
6.4 Output
Short-circuit resistance
6.5 Dimensions, weights
Rod diameter
Nominal length
For Ø 8 mm
For Ø 10.2 mm
Weight (depends on length)
Housing material
Flange material
Rod material
Rod wall thickness
For Ø 8 mm
For Ø 10.2 mm
Housing mounting via threads M18×1.5 or 3/4"-16UNF
Tightening torque
6.6 Maximum sampling rate f
At nominal length
0050...0250 mm
0251...0600 mm
0601...1300 mm
1301...2700 mm
2701...5500 mm
5501...7600 mm
> 7601 mm
Nominal length = 500 mm, magnet in the middle of the measuring range
1)
For : Use in enclosed spaces and up to a height of 2000 m above sea
2)
level.
Individual specifications as per Balluff factory standard, resonant
3)
frequencies excluded
For : The transducer must be externally connected via a limited-
4)
energy circuit as defined in UL 61010-1, a low-power source as defined in
UL 60950-1, or a class 2 power supply as defined in UL 1310 or
UL 1585.
10...30 V DC
≤ 0.5 V
SS
≤ 140 mA to 1524 mm
≤ 180 mA from 1525 mm
≤ 500 mA
Up to 36 V
Up to 36 V
500 V AC
Signal cable to GND
8 mm or 10.2 mm
25...1016 mm
25...7620 mm
Approx. 2 kg/m
Aluminum
Stainless steel
Stainless steel
0.9 mm
2 mm
Max. 100 Nm
max
1160 Hz
1010 Hz
805 Hz
490 Hz
245 Hz
180 Hz
170 Hz