NEC MultiSync FE991SB Manuel De L'utilisateur page 5

Controls
– continued
Size and Position Controls
Left/Right: Moves the image horizontally (left or right).
Down/Up: Moves the image vertically (up or down).
Narrow/Wide: Decreases or increases the horizontal size of the
image.
Short/Tall: Decreases or increases the vertical size of the image.
Color Control System
Colour presets selects the desired colour setting. The bar is
replaced by the colour setting choice. Each colour setting is
adjusted at the factory to the stated Kelvin. If a setting is adjusted,
the name of the setting will change from Kelvin to Custom except
sRGB mode.
Red, Green, Blue: Color Control System decreases or increases
the monitor's red, green or blue colour guns depending upon
which is selected. The change in colour will appear on screen
and the direction (decrease or increase) will be shown by the
bars.
sRGB mode: sRGB mode provides the suitable colour managed
picture image. You can not change Red, Green and Blue colours,
brightness and contrast individually.
Colour Temperature Adjustment: Adjusts the colour temperature
of the screen image.
Geometry Controls
Geometry Controls Menu
The Geometry controls allow you to adjust the curvature or angle
of the sides of your display.
Sides In/Out (pincushion): Decreases or increases the curvature
of the sides either inward or outward.
Sides Left/Right (pincushion balance): Decreases or increases
the curvature of the sides either to the left or right.
Sides Tilt (parallelogram): Decreases or increases the tilt of the
sides either to the left or right.
Sides Align (trapezoidal): Decreases or increases the bottom of
the screen to be the same as the top.
Rotate (raster rotation): Rotates the entire display clockwise or
counterclockwise.
Corner Correction: Allows you to adjust the geometry of the
corners of your display – Top or Bottom.
Tools 1
Moiré Canceler: Moiré is a wavy pattern which can sometimes
appear on the screen. The pattern is repetitive and superimposed
as rippled images. When running certain applications, the wavy
pattern is more evident than in others. To reduce moiré, adjust
the level by using –/+ CONTROL buttons.
Linearity: This selection allows you to adjust the spacing of the
area on the screen. The purpose of this control is to ensure that
a one-inch circle is a true one-inch circle wherever it is on the
screen. The best way to determine the vertical linearity is as
follows:
• Draw equally spaced horizontal lines using a drawing applica-
tion that has a ruler.
• Use the Vertical Balance control to adjust the lines near the
top and bottom of your screen.
• Use the LINEARITY (VER.) control to adjust the spacing be-
tween the lines near the center and top of your screen.
Convergence (FE991 SB only): Aligns all three colors (R,G,B) to
form a single color (white). The purpose of this control is to ensure
that a white line drawn on the screen is as crisp and clear as
possible.
• Use the CONVERGENCE (HOR.) control to adjust the alignment
of the lines in the up/down direction.
• Use the CONVERGENCE (VER.) control to adjust the alignment
of the lines in the left/right direction.
Tools 2
Language: OSM controls menus are available in 6 languages.
OSM Position: You can choose where you would like the
OSM controls menu to appear on your screen. Selecting
OSM Position allows you to manually adjust the OSM controls
menu position from among Center, Top left, Top right, Bottom left
and Bottom right.
OSM Turn Off: The OSM controls menu will stay on as long as it
is in use. In the OSM Turn Off sub-menu, you can select how long
the monitor waits after the last touch of a button for the OSM
controls menu to disappear. The preset choices are 5 thru
120 seconds.
OSM Lock Out: This control completely locks out access to all
OSM controls functions except Brightness and Contrast. When
attempting to activate OSM controls while in the lock out mode, a
screen will appear indicating that OSM controls are locked out.
To activate the OSM Lock Out function, press SELECT and hold +
down simultaneously. To deactivate the OSM Lock Out, press
SELECT and hold + down simultaneously.
IPM System Off Mode:
Enable: The IPM System works normally and all stages of
energy savings are utilized.
Disable: The Off Mode of the IPM System is not used.
NOTE: For standard systems and graphics boards, keep the
factory setting at ENABLE.
EdgeLock Control: Operating your monitor at a nonstandard
timing may cause images to appear darker than normal or have
color distortion. Use of the EdgeLock control will adjust images
to their normal state.
Hot Key: This selection allows you to use
control and –/+ as contrast control.
Factory Preset: Selecting Factory Preset allows you a reset most
OSM control settings back to the factory settings. A warning
statement will appear to confirm that you do want to reset ALL
settings. Individual settings can be reset by highlighting the
control to be reset and pressing the RESET button.
Information
Display Mode: Indicates the current mode and frequency setting
of the monitor.
Monitor Info: Indicates the model and serial numbers of your
monitor.
Refresh Notifier: A message will advise you if the refresh rate of
the signal being applied to the monitor by the computer is too
low. For further information, please refer to your display card or
system manual.
E S Product
NERGY TAR
As an E S Partner,
NERGY TAR
NEC-Mitsubishi Electronics Display of America, Inc. has
determined that this product meets the E
for energy efficiency. The E
represent EPA endorsement of any product or service.
Y
as brightness
/
S guidelines
NERGY TAR
S emblem does not
NERGY TAR
5