Publicité
Les langues disponibles
Les langues disponibles
Kerf Indicator (Fig. I)
The front of the saw base plate has a kerf indicator
and bevel cutting. This indicator enables you to guide the saw
along cutting lines penciled on the material being cut. The kerf
indicator lines up with the left (outer) side of the saw blade,
which makes the slot or "kerf" cut by the moving blade fall to the
right of the indicator. Guide along the penciled cutting line so
that the kerf falls into the waste or surplus material.
Mounting and Adjusting the Parallel
Fence (Fig. N)
The parallel fence
28
is used for cutting parallel to the edge of
the workpiece.
Mounting
1. Slacken the parallel fence adjustment knob
parallel fence to pass.
2. Insert the parallel fence
3. Tighten the parallel fence adjustment knob
Adjusting
1. Slacken the fence adjustment knob
fence
28
to the desired width. The adjustment can be read
on the parallel fence scale.
2. Tighten the fence adjustment knob
Mounting the Dust Extraction Port (Fig. A, P)
Your circular saw is supplied with a dust extraction port.
To Install the Dust Extraction Port
1. Fully loosen depth adjustment lever
2. Place the base plate
5
3. Align the left half of the dust extraction port
blade guard
33
as shown. Be sure to insert the tab into the
casting notch on the tool. When installed correctly, it will
snap fully over the original depth of cut pointer.
4. Align the right-hand piece
5. Insert screws and tighten securely.
Prior to Operation
•
Make sure the guards have been mounted correctly. The saw
blade guard must be in closed position.
•
Make sure the saw blade rotates in the direction of the arrow
on the blade.
•
Do not use excessively worn saw blades.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
9
for vertical
27
to allow the
28
in the base plate as shown.
27
.
27
and set the parallel
27
4
.
in the lowest position.
29
over upper
30
with the left.
Proper Hand Position (Fig. J)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main
handle
26
, with the other hand on the auxiliary handle
LED Worklight (Fig. A)
The LED worklight
15
is activated when the trigger switch is
depressed. When the trigger is released, the worklight will stay
illuminated for up to 20 seconds.
nOTE: The worklight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Switching On and Off (Fig. B)
For safety reasons the trigger switch
with a lock-off button
1
.
Press the lock-off button to unlock the tool.
To run the tool, press the trigger switch
trigger switch is released, the lock-off switch is automatically
activated to prevent unintended starting of the machine.
NOTICE: Do not switch the tool ON or OFF when the saw
blade touches the workpiece or other materials.
Workpiece Support (Fig. J–M)
WARNING: To reduce the risk of serious personal
injury, support the work properly and hold the saw
firmly to prevent loss of control.
Figures J and K show proper sawing position. Figures L and M
show an unsafe condition. Hands should be kept away from
cutting area.
To avoid kickback, ALWAYS support board or panel NEAR the
cut, (Fig. J and K). DON'T support board or panel away from the
cut (Fig. L and M). When operating the saw, keep the cord away
from the cutting area and prevent it from becoming hung up on
the work piece.
ALWAYS DISCONNECT SAW BEFORE MAKING ANY ADJUST-
MENTS! Place the work with its "good" side—the one on which
appearance is most important—down. The saw cuts upward,
so any splintering will be on the work face that is up when you
saw it.
Cutting (Fig. J)
WARNING: Never attempt to use this tool by resting it
upside down on a work surface and bringing the material
to the tool. Always securely clamp the workpiece and bring
the tool to the workpiece, securely holding the tool with
two hands as shown in Figure J.
Place the wider portion of the saw base plate on that part of
the workpiece which is solidly supported, not on the section
that will fall off when the cut is made. As examples, Figure J
illustrates the RIGHT way to cut off the end of a board. Always
clamp work. Don't try to hold short pieces by hand! Remember
EnGLIsH
12
.
2
of your tool is equipped
2
. As soon as the
47
Publicité
