Moen 84431 Manuel D'installation page 3

INSTALLATION INSTRUCTIONS
1
1. Make sure that the mounting surface is clean and dry. Orient deck
gasket as shown, then assemble the deck gasket to the lav
assembly, pushing the gasket around the mounting shanks until it
is seated inside the bottom lip of the escutcheon.
A
1
3
4
6
7
16
13
1. Place plumber's putty (14) under seat (3).
2. Thread mounting nut (6), washer (5) and bottom gasket (4) onto drain body (7).
Wrap top threaded end of drain body with thread seal tape (16).
3. Position drain body up through drain opening and screw seat onto drain body.
4. Align the drain body so that the pivot rod opening faces the rear of the sink and
tighten the mounting nut snug.
5. Apply thread seal tape to the threaded end of tailpiece (13) and screw into the
drain body. Tighten firmly by hand.
6. Drop in drain plug (1) and install pivot rod in one of the following ways:
(A) VANDALPROOF: Prevents unauthorized removal of drain plug. Place pivot
rod seat (8) into opening of drain body as shown. Place the pivot rod (15) into the
opening and position the pivot rod through the drain plug hole as shown in
B
1
3
4
6
13
7
1. Place plumber's putty (14) under seat (3).
2. Drop seat into drain opening in sink.
3. From underneath the sink, slide the bottom gasket (4), mounting washer (5)
and mounting nut (6) onto drain seat and hand tighten.
4. Fit seal (13) inside the drain tailpiece (7).
5. Install the tailpiece and hand tighten. Align the entire assembly so that the pivot
rod opening is facing the rear of the sink, hand tighten the mounting nut (6) until
snug.
6. Drop in drain plug (1) and install pivot rod in one of the following ways:
(A) VANDALPROOF: Prevents unauthorized removal of drain plug. Place pivot
rod seat (8) into opening of tailpiece as shown. Place the pivot rod (15) into the
opening and position the pivot rod through the drain plug hole as shown in
2
1 Drain Plug
2 Lift Rod & Knob
3 Seat
14 11 4 Bottom Gasket
5 Mounting Washer
1
6 Mounting Nut
5
7 Drain Body
8 Pivot Rod Seat
15
8
12
9
2
1 Drain Plug
2 Lift Rod & Knob
3 Seat
14
11 4 Bottom Gasket
5 Mounting Washer
1
6 Mounting Nut
5
7 Tailpiece
8 Pivot Rod Seat
15
8
12
9
2
2. To fasten faucet on basin, adjust the position of the faucet on the basin to best
accommodate bowl size (basin thickness should not exceed 1" (25.4mm). From
under the sink, place the mounting nut/washers on the faucet supplies, large side up.
Thread on mounting nut/washers by hand. Check faucet position. Align and match
escutcheon and escutcheon gasket together. Make final tightening of the mounting
nut/washers by hand.
9 Pivot Nut
10 Lift Rod Strap
11 Lift Rod Strap Screw
12 Spring Clip
13 Tailpiece
14 Plumber's Putty
15 Pivot Rod
16 Teflon Tape
illustration (A) above. Slide the pivot nut (9) onto the pivot rod and thread it snugly
onto the drain body, be careful not to overtighten.
(B) EASY REMOVAL: For quick removal of drain plug for cleaning, follow
instructions above except position parts as shown in illustration (B) above.
7. With lift rod (2) in position on the faucet, insert the end into the lift rod strap (10)
and secure with lift rod strap screw (11).
8. Connect the pivot rod (15) to lift rod strap using spring clip (12) as shown
above.
9. Place the drain plug in the full open position, loosen lift rod strap screw and
adjust the lift rod height so that the knob clears the faucet. Tighten the lift rod
strap screw. Installation is now complete.
9 Pivot Nut
10 Lift Rod Strap
11 Lift Rod Strap Screw
12 Spring Clip
13 Seal
14 Plumber's Putty
15 Pivot Rod
illustration (A) above. Slide the pivot nut (9) onto the pivot rod and thread it snugly
onto the drain body, be careful not to overtighten.
(B) EASY REMOVAL: For quick removal of drain plug for cleaning, follow
instructions above except position parts as shown in illustration (B) above.
7. With lift rod (2) in position on the faucet, insert the end into the lift rod strap (10)
and secure with lift rod strap screw (11).
8. Connect the pivot rod (15) to the lift rod strap using the spring clip (12) as
shown above.
9. Place the drain plug in the full open position, loosen lift rod strap screw and
adjust lift rod height so that the knob clears the faucet. Tighten the lift rod strap
screw. Installation is now complete.
1
15
(A)
1
15
(B)
1
15
(A)
1
15
(B)
2