Recommended Maintenance; Lubrication; Routine Inspection; Replacing Sanding Sleeves - Delta 31-483 Manuel D'utilisation

NOTE: Disconnect machine from power source before
performing any maintenance.

LUBRICATION

All bearings are sealed and permanently lubricated. No
further lubrication is needed.

ROUTINE INSPECTION

It is recommended that you periodically inspect your
spindle sander as a precautionary action. During this
time, check for the following:
• Inspect all hardware, fittings and fasteners that may
have loosened due to vibration and re-tighten as
needed.
• Check for dust and/or wood particles that may have
accumulated on or in the machine. Check all dust
collection fittings – re-tighten as needed.
• Inspect the ON/OFF SWITCH for damage before each
use. Periodically inspect the power cord and plug for
damage. If necessary replace the power cord and the
plug at the first signs of visible damage.
• Check all table inserts, spindles and sanding sleeves
for damage and replace if necessary.
A complete line of accessories is available from your DELTA
DELTA Factory Service Centers, and DELTA
®
DeltaMachinery.com for an online catalog or for the name or your nearest supplier.
Since accessories other than those offered by dELTA
use of such accessories could be hazardous. For safest operation, only dELTA
accessories should be used with this product.
To register your tool for warranty service visit our website at www.DeltaMachinery.com.
dELTA will repair or replace, at its expense and at its option, any new dELTA
®
use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a dELTA
center or authorized service station with proof of purchase of the product within five years and provides dELTA
to verify the alleged defect by inspection. For all refurbished dELTA
for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone
other than an authorized dELTA
damages resulting from defective products. Some states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you. This warranty is dELTA
with respect to defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are
expressly disclaimed by dELTA
1-800-223-7278. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America,
see country specific warranty information contained in the packaging, call the local company or see website for warranty
information.

RECOMMENdEd MAINTENANCE

ACCESSORIES

Authorized Service Centers. Please visit our Web Site www.
®

wARRANTY

Five Year Limited New Product warranty
service facility or representative. Under no circumstances will dELTA
®
. For further detail of warranty coverage and warranty repair information, visit www.deltaMachinery.com or call
®
REPLACINg THE SANdINg
SLEEvES
Make sure that the switch is in "OFF"
position and that the power cord is
unplugged.
NOTE: Reverse threads are used to attach the spindle
to the machine.
• Remove the table insert by lifting it up and over the
sanding spindle.
• Using two 17 mm wrenches, as shown in Figure 4
(page 8), loosen the spindle by turning it clockwise.
• With the 17 mm wrench still positioned on the spindle
seat, unscrew (clockwise) the spindle with your hand
and remove.
• To remove the ¼", ½", or
the Phillips head screw at the bottom of the spindle
and pull the sanding sleeve and spindle apart.
To remove the 1 ½" or 2" sanding sleeve, use the
supplied 12 mm wrench to loosen (clockwise) the nut
at the top of the spindle. Pull the sanding sleeve and
spindle apart.
• To install a new sanding sleeve, follow the directions
on page 8 (INSTALL SANDING SLEEVES ONTO
SPINDLES).
Supplier, DELTA
®
have not been tested with this product,
®
machine, machine part, or machine accessory which in normal
®
product, the warranty period is 180 days. dELTA
®
's sole warranty and sets forth the customer's exclusive remedy,
®
12
5 / " sanding sleeve, loosen
8
Factory Service Centers, and
®
recommended
®
factory service
®
with reasonable opportunity
®
will not be responsible
®
be liable for incidental or consequential
®