TECHNICAL DATA
CORDLESS DRILL DRIVER
Production code..........................................................................
Drilling capacity in steel ..............................................................
Drilling capacity in wood .............................................................
Wood screws (without pre-drilling) .............................................
No-load speed 1st gear ..............................................................
No-load speed 2nd gear .............................................................
Torque ........................................................................................
Battery voltage............................................................................
Drill chuck range .........................................................................
Weight according EPTA-Procedure 01/2003 ..............................
Noise/vibration information
Measured values determined according to EN 60 745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ...........................
Sound power level (Uncertainty K=3dB(A)) ................................
Wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 60745.
Vibration emission value
Drilling into metal a
..............................................................
h.D
Uncertainty K= ........................................................................
Screwing a
.............................................................................
h
Uncertainty K= ........................................................................
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745
and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with
different accessories or poorly maintained, the vibration emission may differ. This may signifi cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running
but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
DRILL SAFETY WARNINGS
Use auxiliary handle(s), if supplied with the tool. Loss of control
can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring.
Cutting accessory contacting a „live" wire may make exposed
metal parts of the power tool „live" and could give the operator an
electric shock.
SCREWDRIVER SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give the
operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Wear a suitable dust protection mask.
16
ENGLISH
BS12 G3
BS12 G3
BS14 G3
BS14 G3
Li-Ion 1,5 Ah
Li-Ion 2,0 Ah
Li-Ion 1,5 Ah
Li-Ion 1,5 Ah
......4522 58 01... ..............4521 87 01... ...............4523 02 01... ...............4569 84 01... ................4521 89 01...
...000001-999999 ........ ...000001-999999....... ...000001-999999 .... . ...000001-999999 .........000001-999999
........ 10 mm ................. 10 mm ..................10 mm ..................10 mm .................13 mm
........ 30 mm ................. 30 mm ..................30 mm ..................30 mm .................32 mm
.......... 5 mm ................... 5 mm ....................5 mm ....................5 mm ...................5 mm
...... 350 min
-1
............. 350 min
-1
..............400 min
-1
..............400 min
.... 1500 min
-1
........... 1500 min
-1
............1700 min
-1
............1700 min
........ 30 Nm ................. 32 Nm ..................32 Nm ..................32 Nm ..................36 Nm
........ 12 V .................... 12 V ..................14,4 V ..................14,4 V ..................14,4 V
.. 0,8-10 mm ........... 0,8-10 mm ........... 0,8-10 mm ............2,0-13 mm ...........2,0-13 mm
....... 1,1 kg .................. 1,1 kg ...................1,2 kg ...................1,2 kg ...................1,2 kg
..... 84,5 dB (A) .......... 84,5 dB (A)...........86,5 dB (A) ..........86,5 dB (A) ..........86,5 dB (A)
..... 95,5 dB (A) .......... 95,5 dB (A)...........97,5 dB (A) ..........97,5 dB (A) ..........97,5 dB (A)
....... 0,5 m/s
2
............... 0,5 m/s
2
................1,2 m/s
2
................1,2 m/s
....... 1,5 m/s
2
............... 1,5 m/s
2
................1,5 m/s
2
................1,5 m/s
....... 0,7 m/s
2
............... 0,7 m/s
2
................2,0 m/s
2
................2,0 m/s
....... 1,5 m/s
2
............... 1,5 m/s
2
................1,5 m/s
2
................1,5 m/s
Do not machine any materials that present a danger to health (e.g.
asbestos).
Switch the device off immediately if the insertion tool stalls! Do not
switch the device on again while the insertion tool is stalled, as
doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine is
running.
When working in walls ceiling, or fl oor, take care to avoid electric
cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by
burning them. AEG Distributors offer to retrieve old batteries to
protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
BS14 G3
Use only AL1214G3 chargers for charging System L1215G3,
Li-Ion 2,0 Ah
L1220G3, L1415G3 and L1420G3 battery packs. Do not use
battery packs from other systems.
Never break open battery packs and chargers and store only in dry
rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
-1
..............400 min
-1
it off immediately with soap and water. In case of eye contact rinse
-1
............1700 min
-1
thoroughly for at least 10 minutes and immediately seek medical
attention.
SPECIFIED CONDITIONS OF USE
The battery drill/screwdriver is designed for drilling and
screwdriving for independent use away from mains supply.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant provisions
of the directives 2011/65/EU (RoHs), 2014/30/EU, 2006/42/EC and
the following harmonized standards have been used:
EN 60745-1:2009 + A11:2010
2
...............1,2 m/s
2
EN 60745-2-1:2010
2
...............1,5 m/s
2
EN 60745-2-2:2010
2
...............2,0 m/s
2
EN 55014-1:2006 + A1:2009 + A2:2011
2
...............1,5 m/s
2
EN 55014-2:1997 + A1:2001 + A2:2008
EN 50581:2012
Winnenden, 2016-03-29
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and
away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION LI-ION BATTERY
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life.
Under extreme stress the battery electronics switch off the
machine automatically. To restart, switch the machine off and then
on again. If the machine does not start up again, the battery pack
may have discharged completely. In this case it must be recharged
in the battery charger.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance
with local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and insulated
to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
Use only AEG accessories and spare parts. Should components
need to be replaced which have not been described, please
contact one of our AEG service agents (see our list of guarantee/
service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the machine type printed as well as the six-digit No. on the
label and order the drawing at your local service agents or directly
at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work
on the machine.
Please read the instructions carefully before
starting the machine.
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that have
reached the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
Check with your local authority or retailer for
recycling advice and collection point.
European Conformity Mark
National mark of conformity Ukraine
EurAsian Conformity Mark.
ENGLISH
17