Publicité
Les langues disponibles
Les langues disponibles
5.
Disconnect the connection of the safety switch di-
sconnector cable (64) and the engine connection
cable (65).
6.
Disassemble the feed funnel (1) and the ejector
chamber (11) and remove the feed funnel rubber
seal (A) and the ejector chamber rubber seal (B).
Use a 16 mm open-ended spanner/ratchet spanner
to fit the hexagonal bolts (C) and a 17 mm open-end-
ed spanner/ratchet spanner for the locknuts (J).
7.
Clean inside the device and the cutter disc (45)
with compressed air in order to remove shredded
material residues.
8.
Fit the feed funnel (1) and the ejector chamber
(11) with the feed funnel rubber seal (A) and the
ejector chamber rubber seal (B).
12. Transport
Tools required (not included in the scope of delivery):
- Petrol extraction pump
- Suitable vehicle
12.1
Preparing for transport (Fig. 14, 16, 20, 28, 29)
1.
Empty the fuel tank (14) using a petrol extraction
pump (see section 13.7).
Warning: Do not remove the petrol in enclosed
spaces, near fire or when smoking. Petrol fumes
can cause explosions and fire.
2.
The ignition key (33) must always be removed from
the ignition lock (34) and stored securely to pre-
vent unauthorised or improper use by children and
other persons.
3.
Remove the spark plug connector (59) from the
spark plug (60).
4.
Clean the device.
12.2 Transporting without vehicle (Fig. 1, 9)
m Attention: If the unit is to be transported, the
engine must be switched off and the spark plug
connector disconnected.
1.
In order to move the device, grip the ball holder (9)
and tilt the device backwards.
2.
You can now transport the device.
12.3
Transporting with a vehicle (Fig. 8-9)
m Attention: The unit does not have road approv-
al and is therefore not intended for use on public
roads. The device may only be used on cordoned
off premises that are fenced in, attached to a vehi-
cle and moved using it.
48 | GB
1.
In order to move the device with a vehicle, you
must fold the foot (8) in.
2.
Loosen the safety cotter pin on the locking pin (21)
and pull the locking pin (21) out.
3.
Fold the foot (8) up.
4.
Attach the locking pin (21) to the lock in order to
secure the foot (8). This prevents it falling down. Se-
cure the locking pin (21) with the safety cotter pin.
5.
Attach the ball holder (9) to the trailer coupling on
a suitable vehicle.
6.
Take the securing chain (63) and hang it on the
trailer hitch. The securing chain (63) serves as
an additional securing connection should the ball
mount (9) become detached from the trailer hitch.
Note: Ensure that the lock on the ball holder (9) latches
into place.
13. Maintenance
m WARNING!
In the event that the user is to perform mainte-
nance and service work, the user must possess
the necessary technical skills.
If the device is shut down for maintenance, inspec-
tion or storage, turn off the engine, disconnect the
spark plug connector from the spark plug, remove
the ignition key from the ignition and ensure that
all rotating parts have stopped.
m Attention!
To ensure that the motor (4) is no longer running, carry
out a visual inspection.
A two-colour pulley can be seen under the belt cover
(20). This must no longer rotate!
All protective and safety equipment must be reas-
sembled immediately after repair, maintenance is
completed.
Secure the device to prevent an inadvertent start-up
before carrying out maintenance and/or servicing
work:
- Switch off the engine (4) before carrying out any
cleaning or maintenance work.
- Allow the engine (4) to cool down.
- Remove the spark plug connector (59) from the
spark plug (60). Also remove the ignition key (33)
from the ignition (34).
Publicité
