Publicité
Les langues disponibles
Les langues disponibles
• With accessories as well as wearing parts and spare
parts use only original parts. Spare parts can be ob-
tained from your specialist dealer.
• When ordering, please provide our article number,
the type and year of manufacture for your device.
m DANGER!
The device and the packaging are not children's
toys!
Do not let children play with plastic bags, films or
small parts! There is a danger of choking or suf-
focating!
8. Assembly
m ATTENTION!
Always make sure the device is fully assembled
before commissioning!
m Attention! Due to the heavy device weight, we
recommend assembly by at least three people.
Tools required (not included in the scope of delivery):
- 1x pad
- 2x open-ended spanner, size 8 mm
- 1x open-ended spanner, size 13 mm
- 1x open-ended spanner/ratchet spanner, size 16 mm
- 1x open-end wrench/ratchet spanner SW 17 mm
- 3x square timbers
8.1
Fitting the wheels (6) (Fig. 1, 4)
1.
Place a pad on the floor to avoid damage to the de-
vice.
2.
Carefully remove the device from the pallet with
two other people.
3.
Tilt the shredding unit (5) forward slightly.
4.
Fit the wheels (6) by aligning the fitting holes on the
wheels (6) with the fitting holes on the shredding unit
(5) and secure with four hexagonal bolts (C), spring
washers (H), washers (I) and locknuts (J) each. Use
a 16 mm open-ended spanner/ratchet spanner to fit
the hexagonal bolts (C) and a 17 mm open-end-
ed spanner/ratchet spanner for the locknuts (J).
Ensure that the locknuts (J) are on the inside.
NOTE! When mounting, pay attention to the run-
ning direction of the wheels (6).
8.2 Fitting the feed funnel (1) (Fig. 2, 5, 6)
1.
Now place the chopping unit (5) backwards on the
wheels (6).
2.
Position the feed funnel (1) with the feed funnel
rubber seal (A) over the shredding unit (5) and en-
sure that the fitting holes are aligned.
3.
Screw the feed funnel (1) tight to the shredding unit
(5) using four hexagonal bolts (D), spring washers
(H), washers (I) and two locknuts (J). Use a 16
mm open-ended spanner/ratchet spanner to fit
the hexagonal bolts (D) and a 17 mm open-ended
spanner/ratchet spanner for the locknuts (J).
4.
In order to activate the EMERGENCY STOP bow
(27), connect the safety switch connection cable
(28) for the safety switch (26) to the engine con-
nection cable (29).
5.
Connect the safety switch disconnector cable
(64) to the engine connection cable (65).
8.3
Mounting the foot (8) (Fig. 7-9)
1.
Connect the drawbar (10) to the foot bracket (7)
by pushing the drawbar (10) into the foot bracket
recess (7) until the fitting holes are aligned.
2.
Attach the drawbar (10) to the foot bracket (7) using
two hexagonal bolts (F), spring washers (H), wash-
ers (I) and locknuts (J). Use a 16 mm open-ended
spanner/ratchet spanner to fit the hexagonal bolts
(F) and a 17 mm open-ended spanner/ratchet
spanner for the locknuts (J).
3.
Place the foot bracket (7) on the foot (8) and posi-
tion the fitting holes so that they are aligned.
4.
Screw the foot (8) to the foot bracket (7) us-
ing the hexagonal bolt (G), the spring wash-
er (H), the locking lug on the locking pin (21),
the washer (I) and the locknut (J). Use a 16 mm
open-ended spanner/ratchet spanner to fit the
hexagonal bolts (G) and a 17 mm open-ended
spanner/ratchet spanner for the locknuts (J).
Ensure that you also install the locking lug on the
locking pin (21)!
5.
Unfold the foot (8) and secure it with the locking pin (21).
6.
Grip the device on the feed funnel (1) and tilt it for-
wards until it is on the foot (8).
8.4
Installing the drawbar (10) on the shredding
unit (5) (Fig. 10)
1.
Place two pieces of square timber in front of and
behind the wheels (6) so that the device does not
roll away when tilting.
2.
Place another piece of square timber (approx. 10
cm thick around 1 m away from the shredding unit
(5)) on the floor.
3.
Grip the device on the feed funnel (1) and tilt it
backwards until it is on the square timber.
GB | 43
Publicité
