Publicité
Les langues disponibles
Les langues disponibles
10.4
Switching the engine (4) off
(Fig. 1, 14, 19, 20)
Note: Allow the device to run for a short time (approx.
30 seconds) switching it off so that the engine (4) can
cool down.
1.
Use the throttle (42) to set the speed to MIN, "tor-
toise".
2.
Turn the ignition key (33) to the "Switch off" posi-
tion, (30).
3.
Remove the ignition key (33) and store it in a safe
place.
4.
Set the fuel valve (41) to the "OFF" position.
Note: You can only remove the ignition key (33) when
the "Switch off" position (30) is selected.
m ATTENTION! In order to switch the device off in
the event of an emergency, actuate the EMERGEN-
CY STOP bow (27) by pressing the EMERGENCY
STOP bow (27) against the safety switch (26).
m ATTENTION! Even after the EMERGENCY STOP
bow (27) has been actuated, the blades (46) contin-
ue to rotate for a few seconds, depending on the
speed set.
Note: Do not use the EMERGENCY STOP bow (27)
routinely to stop the device.
10.5
Overload protection (Fig. 1, 14)
The device is equipped with overload protection. If the
engine is overloaded, this switches off automatically to
protect the device from overheating.
1.
If the overload protection has triggered, switch the
device off and wait until the engine (4) has cooled
down.
2.
Now press the reset switch (35) on the control pan-
el (3) and switch the device on again.
10.6
Automatic oil cut-off
The automatic oil cut-off system responds when
there is too little engine oil.
1.
If the oil level is too low, top up the oil as described
in 9.1.
2.
Start the engine (4) as described in 10.1.
11. Cleaning
Danger!
Always shut the engine down and remove the spark
plug connector and ignition key before carrying out any
cleaning work.
m Attention! Never use a high-pressure cleaner to
clean your machine.
The use of high-pressure cleaners shortens the
service life and reduces the ease of maintenance.
• Keep protective devices, air vents and the motor
housing as free of dust and dirt as possible. Rub
the device clean with a clean cloth or blow it off with
compressed air at low pressure.
• We recommend that you clean the device directly
after every use.
• Clean the device at regular intervals using a damp
cloth and a little soft soap. Do not use any cleaning
products or solvents; they could attack the plastic
parts of the device. Make sure that no water can
penetrate the device interior. Water entering a power
tool will increase the risk of electric shock.
Tools required (not included in the scope of delivery):
- Open-ended spanner, size 10 mm
- Open-ended spanner/ratchet spanner, size 16 mm
- Open-ended spanner/ratchet spanner, size 17 mm
- Brush or compressed air
11.1
Cleaning the V-belts (56) (Fig. 2, 14, 25, 28)
1.
Place the device on a level, even surface.
2.
Remove the ignition key (33) from the ignition lock
(34).
3.
Remove the spark plug connector (59) from the
spark plug (60).
4.
Remove the V-belt cover (20) by unscrewing the four
hexagonal bolts using a 10 mm open-ended spanner.
5.
Clean the transmission elements and the two
V-belts (56) once to twice per year using a brush
or compressed air.
6.
Re-attach the V-belt cover (20) and secure it with
four hexagonal bolts.
11.2
Removing blockages and shredded material
residues from the cutter disc (45)
(Fig. 2, 5, 14, 29)
Switch the machine off to rectify faults or to
remove jammed pieces of wood.
1.
Place the device on a level, even surface.
2.
Remove the ignition key (33) from the ignition lock
(34).
3.
Remove the spark plug connector (59) from the
spark plug (60).
4.
Disconnect the safety switch connection cable
(28) and the engine connection cable (29).
GB | 47
Publicité
