DeWalt DCS369M2-QW Mode D'emploi page 35

Date Code Position (Fig. B)
The date code 10 , which also includes the year of manufacture,
is printed into the housing.
Example:
2019 XX XX
Year of Manufacture
Description (Fig. A, B)

WARNING: Never modify the power tool or any part of it.
Damage or personal injury could result.
Variable speed trigger switch
1
Lock-off button
2
Blade clamp
3
Pivoting shoe
4
Hand grip
5
Battery pack
6
Battery release button
7
Main handle
8
Worklight
9
Datecode
10
Intended Use
Your DCS369 cordless reciprocating sabre saw has been
designed for professional sawing of wood, metal and tubes. The
compact design permits cutting extremely close to the edge of
difficult areas.
DO nOT use under wet conditions or in the presence of
flammable liquids or gases.
This reciprocating saw is a professional power tool.
DO nOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
this tool.
Young children and the infirm. This appliance is not
•
intended for use by young children or infirm persons
without supervision.
• This product is not intended for use by persons (including
children) suffering from diminished physical, sensory or
mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Use only D
e
Inserting and Removing the Battery Pack
from the Tool (Fig. B)
nOTE: Make sure your battery pack
WALT battery packs and chargers.
6 is fully charged.
To Install the Battery Pack into the Tool Handle
1. Align the battery pack 6 with the rails inside the tool's
handle (Fig. B).
2. Slide it into the handle until the battery pack is firmly seated
in the tool and ensure that you hear the lock snap into place.
To Remove the Battery Pack from the Tool
1. Press the release button 7
out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button . A combination of the three green LED lights will
12
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Belt Hook (Fig. J)
Optional Accessories

WARNING: To reduce the risk of serious personal
injury, DO NOT suspend tool overhead or suspend
objects from the belt hook. ONLY hang tool's belt hook
from a work belt.

WARNING: To reduce the risk of serious personal
injury, ensure the screw holding the belt hook is secure.
IMPORTanT: When attaching or replacing a belt hook, use only
the screw that is provided. Be sure to securely tighten the screw.
A belt hook can be be attached to either side of the tool
14
using only the screw 15 provided, to accommodate left- or
right-handed users. If the belt hook is not desired at all, it can be
removed from the tool.
To move the belt hook, remove the screw
place then reassemble on the opposite side. Be sure to securely
tighten the screw.
Variable Speed Trigger Switch (Fig. E)
Lock-off Button and Trigger switch
Your saw is equipped with a lock-off button
To lock the trigger switch, press the lock-off button on the
left. Always lock the trigger switch
the tool to eliminate unintentional starting.
To unlock the trigger switch, press the lock-off button on the
right. Pull the trigger switch to turn the motor ON. Releasing the
trigger switch turns the motor OFF.

WARNING: This tool has no provision to lock the switch
in the ON position, and should never be locked ON by any
other means.
EnGLIsh
and firmly pull the battery pack
15 that holds it in
.
2
1 when carrying or storing
33