Installing The Control Panel; Calibrating The Trivet - Hatco IWRM-UT Série Manuel D'installation Et D'utilisation

INSTALLATION

Installing the Control Panel

Use the following procedure to install the control panel.
Remote mounted control panel must be mounted on a
vertical wall and installed in vertical position. Mounting
control panel in horizontal position may result in collection
of liquids and lead to an electric shock.
1. Carefully measure and cut the opening in the cabinet wall
for the control panel.
Silicone Sealant
Cabinet Wall Cabinet Wall
Mounting Screw Hole
Control Panel Cutout Dimensions
2. Position the control panel into the cutout opening through
the front of the cabinet, and mark the locations for the four
mounting screw holes. Remove the control panel from the
cutout opening.
3. Drill the holes for the control panel mounting screws (not
supplied).
4. Apply a 1/4" (6 mm) bead of NSF-approved silicone sealant
where the trim on the control panel will contact the cabinet
surface. Refer to the "Control Panel Cutout Dimensions"
illustration for silicone placement.
5. Position the control panel into the cutout opening through
the front of the cabinet. Make sure to embed the trim on the
control panel into the silicone.
6. Fasten the control panel to the vertical surface using four
mounting screws (not supplied).
7. Connect the control cable on the control panel to the control
cable port on the bottom of the induction range.
Silicone
Sealant
Mounting
Screw
Installing the Control Panel
WARNING
2-1/4"
(55 mm)
5-7/16"
(138 mm)
C a b in e t W C a b in e t W
a ll a ll
Control Cable

Calibrating the Trivet

After installation and before the first use of the Induction
Warmer, the trivet must be calibrated to compensate for the
installation location. Use the following procedure to calibrate
the trivet.
NOTE: The unit should be plugged in for a minimum of 30
minutes before starting the calibration process.
1. Make sure the unit is plugged into a properly grounded
electrical receptacle of the correct voltage, size, and plug
configuration. See the SPECIFICATIONS section for
details.
2. Clear all objects from the surface of the countertop where
the unit is installed.
• Make sure there are no magnets or ferrous materials on
the countertop.
• DO NOT place the trivet on countertop, at this time.
3. Mark the approximate center of the unit on the surface of
the countertop using a piece of tape or sticker.
4. Press the button to turn on the unit.
• The green indicator on the
• At first startup, and anytime the trivet is missing, the LED
display will read "NO TRIVET". The unit will beep slowly.
5. Press and hold both the
approximately three seconds.
• The LED display will read "CAL".
6. Press the button to begin calibration step 1, which
compensates for background noise.
• The LED display will flash "STP1".
• When step 1 is finished, a long beep will sound and
the LED display will read "DONE" (approximately 20
seconds).
7. Place the trivet on the countertop, close to the center of the
unit installed underneath the countertop.
8. Press the button to begin calibration step 2, which
determines the center location of the trivet.
• The LED display will read "STP2".
9. Continuously slide the trivet slowly on the countertop
around the center of the Induction Warmer to allow the unit
to determine the center location and account for installation
variations.
• While moving the trivet, the LED display will show
numbers between 0 and 250. Search for the location that
reads the highest number.
• When step 2 is finished, a long beep will sound and
the LED display will read "SAVE", then "DONE"
(approximately 30 seconds).
10. Press the button to complete and exit calibration.
8
English
button will illuminate.
and buttons for
Form No. IWRMUM-0321